This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Hi,
I'm trying to connect and discover services of a BLE device equipped with a nrf52832. The device advertises correctly and i can see it on the nrf Connect app on both...
Hi All,
i would like to know how gpio relate to gpiote,i go through some code and find
out , that gpiote handles in,out,config registers that is handle by gpio also ...
Hi nordic guys,
I have built a project based on ble_app_hids_keyboard demo in SDK12.3.0.This is a new hid deive which is microsoft defined in win10.The sample report is...
I have few questions on BLE in rigado based on my requirement needs,
I need Dynamic data transfer in beacon mode, is it possible in Beacon mode without Rigado BLE stack...
Hello,
I get two errors when compiling examples\ble_peripheral\ble_app_uart with IAR 8.11. I have ble_app_uart_pca10040_s132 - nrf52832_xxaa as the active project.
I...
registered_handler_get() in ble_db_discovery.c searches a table for the appropriate handler to call for a given UUID.
However, ble_db_discovery_evt_register() assigns the...
Hi,
In the Getting Started guide of the Bluetooth Mesh SDK it is stated that legacy non-mesh devices can communicate with the mesh via a proxy mesh device through tunneling...
Hi everyone,
I am using the PCA10001 eval board and I have been able to get things up and running using the mbed platform but now I am implementing a timer based interrupt...
Hi All,
I'm currently designing my implementation of BLE Services/Characteristics and wanted a quick review to make sure I'm on the right path based on my implementation...
Hi,
I have couple of nRF52832 boards, nRF5-SDK-for-Mesh (v. 0.9.2) and good will to demonstrate some simple multihop mesh.
I already tested the light control example...
Hello,
There is gonna be a tech tour in my country(Israel) soon and I am planning to purchase 2 nrf52832 Development kits does anybody know if it will be available there...
Hi! I want to use the "cube" animation from android thingy app, with my custom board.
When I scaned in first place I couldn't see my board. It was solved adding the ble_tcs...
Hi,
Is it safe to backfeed some current into the PPK.
I use the PPK to measure the power consumption of a battery powered IoT device. I disconnect the battery and use the...
It looks like the "NRF52-DK" development kit I can find comes with an nRF52832 chip, but I'm looking to get a dev kit to develop for the nRF52810. I did also find a "NRF52840...
Hi: it's me again, sorry to bother everyone once more.
This time I can finish provisioning... almost. You see, at the end of the whole provision process, a function must...
