Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
I've developed an application on the nRF51 DK, now for further testing purposes I need to upload it to the nRF Beacon (PCA20006).
My software uses SDK8 (S11 v8) and it...
I want to get rid of the board support package, and write my own code to interface with the least complicated drivers for UART, BLE and SPI etc.
If I remove BSP I ifind...
hi i have pca 10001 eval kit .I need to connect it with PIC16L1947 controller via uart.The data transmitted from pic is to be collected by nrf51822 and it should send as advertisement...
I am developing an application from scratch for the pca10001 by copying a lot of code from the heart rate example.
When calling "softdevice_ble_evt_handler_set" I get an...
I am looking over the stack-up for the dev board which I received from an FAE and has designed in a 50mil width PCB antenna. I am using this online calculator here:
emclab...
Hello--
The nRF51-Dongle has these 20 pads which I think correspond to a debug port:
On the schematic, it looks like these feed into JTAG signals:
My question...
Hello,
I just got a nRF51 DK and I'm trying the examples of nRF folder in the Pack distribution (SDK 7.2).
I can compile the Blinky project but its not working if I...
i have the nRF51DK that comes with the Segger j-link programmer. Can i use the programmer on the board to program a custom board i purchased from Nordic preferred vendor?...
Hi all,
I am using gcc for my Nordic project and I wanted to add the bootloader. After some reading and experimenting the bootloader worked. Now I thought of making a release...
Hello all,
i am trying to make working the ble bootloader from SDK 6.1 with SoftDevice 7.0.0 and gcc setup (pure Eclipse gcc project frome here devzone.nordicsemi.com/.....
Hi,
I need to develop a BLE service for file transfer between iphone and my device. I chose BLE because the files are very small in size, and as BLE does not need authentication...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I have been using the MCP along with the provided dongle to access a custom BLE service. I would like to build a custom windows 7 application around the BLE service and move...
The below source is mine.
ble_app_beacon.zip
I know that it is possible to display the information in the manufacturer data or service data.
I chose which manufacturer...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
