How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
We found a problem with a client's legacy design. They use two 12 pF load capacitors for the 32 MHz crystal, which has a 4 pF capacitance. This is a somewhat unusual Abracon...
Hello DevZone,
I have a project where I currently use the AT%XPOFWARN feature, in order to turn off the modem in case the battery voltage is too low. It's used in both cellular...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
I'm currently using nRF Connect (windows), in conjunction with the PCA10028 board, as GATT server so I can provide a default test service to be consumed by other devices under...
Hi
An unprovisioned device will advertise a beacon and the spec says that it shall be advertised with non-connectable and non-scannable undirected advertising events
...
Hello there,
for a project I would like to use the Arduino Primo core with the nRF52832 chip to read a NFC Tag.
I could not figure why it can´t read a tag even though...
Hi,
I've test the light_control example with the PCA10028 & PCA10040 recently. The PCA10040 was test and it works normally, but the PCA10028 does not.
I have also checked...
I am working on an application that allocate data dynamically at initialization, and my malloc/calloc returns NULL a lot earlier than I expected.
Using a debug macro, I...
Use the E: \ Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart \ pca10040 this routine
Run to chart a breakpoint on the resumption of here
...
Hi guys,
I'm trying to use the HFCLK to generate high resolution timing. Ideally at the millisecond resolution. I've written a layer around the nrf_drv_timer.c module....
Hi,
I followed the tutorials you made to start developing BLE applications for nRF52 series development board. Then I started to make my custom application (in fact, it...
Hi everyone,
I have been reading the Specifications of Bluetooth 4.1, mostly about Universally Unique Identifiers (UUIDs) for Services, Characteristics, etc.
I found...
Respected sir,
setup for programming = Eclipse-gcc-toolchain-setup
board = PCA10040
as per my way first take a ble_app_uart code startup my coading purpose.
then we...
Hi Guys,
I'm doing the following before putting my device to sleep. This works fine when I use NRF_POWER->SYSTEMOFF, but when I use sd_power_system_off(), it doesn't seem...
Hello,
I am using nRF52832 development kit. I used different examples to send data. But i couldn't accomplish to send data packet over 20 byte. The max data size is defined...
I'm planning to use nRF51422 QFAAE00 as ble central. I try to compile the SDKv10.0.0\examples\ble_central\ble_app_hrs_c and SD130. And another one as ble peripheral using...
Anyone had a successful attempt at using the fds(flash data storage) module( http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v11.0.0%2Flib_fds...
