Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
According to the description of S132_SDS_v5.0 on page 82, when the establishment of connection, in accordance with the BLE protocol, softdevice will be interrupted frequent...
I am using nRF52840 and the power profiler. I am trying to measure the current to evaluate the scheduling of BLE. Now I am using the ble_uart_c example and I changed the scan_interval...
I'm trying to set up SPI example from SDK12.3, but I get error at line 53 of main.c
static const nrf_drv_spi_t spi = NRF_DRV_SPI_INSTANCE(SPI_INSTANCE);
It's saying...
Dear friends,
i am using Power Profiler Kit with a nRF52832 DK(PCA10036). However, i just find three versions of SDK on www.nordicsemi.com/.../nRF52-DK . My problem is that...
Hi nordic,
nRF5_SDK_14.0.0_3bcc1f7\Raga\examples\ble_peripheral\ble_app_ancs_c FDS\pca10040\s132\arm5_no_packs
I had a problem when I was using FDS，When I use the GC...
Dear friends,
I want to use Power Profiler Kit to monitor the current waves of nRF5x DK, and i followed the following configurations:
The PPK board (PCA63511) is connected...
How do you do
Now use E: \ Nordic \ nRF5_SDK_12 2.0 \ examples \ peripheral \ pwm_driver \ pca10040 demo5 pwm_driver routine
There are two problems:
How to change...
I run into this topic during seeking an answer to my problem and for me, as well as for the author of that question the answer doesn't work properly. But wouldn't it be easier...
I was able to create a Distribution package with the command as shown in the following photo.
I have taken the zip file from email app in my iPhone and have opened in...
Programming the bootloader
How the MBR knows the start address of the bootloader?
pape says : This start address is defined in UICR.BOOTLOADERADDR, which is located at...
How do you do
1.Now want to set the PWM output frequency is 60 hz, but with an oscilloscope test is 60.24 hz, here more than 0.24 hz.How can I do the precision of the precision...
Hello,
I'm trying to connect my Linux computer to the nrF52 DK card using BLE.
I'm connecting my Bluetooth chip to nrF52 and I want to display "hello" on the serial interface...
