I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
Hello, I am having issue to migrate a working project based on Azure IoT Hub Application code from 1.7.0 to 2.7.0, I have resolved all errors associated with changing the...
I'm running the peripheral_ancs_client using the 2.9.0 SDK on a nRF5340-DK. On an iPhone running iOS18, the device is not visible under Settings->Bluetooth when the nRF5340...
This feature used to be helpful pre version 2.7 or so, but has persisted as an issue since then. All of the configs in any *.conf are all underlined and have this phrase when...
Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hello,
I am developping an application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) extended advertising on SDK 2.7.0.
costum chip nrf52840 (on...
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
I have run into two SAADC issues on the nRF52832 using SDK v12.1.0. Any recommendations on how to fix them?
Issue 1:
When the Keil compiler optimization is turned up...
Hi,
Has anything changed in subject of one peripheral connecting to multiple central devices? All I need is little number (~3) of concurrent links with mobile phones.
I have been working on a custom board that uses a taiyo yoden EYSHJNZXZ module.
A tact switch is connected between P0.21 and GND.
I want to use this switch simple input...
Hi All!
I'm working a few weeks now with the NRF52 DK and having loads of fun!
Today I tried to make a central/scanner that scans for packages from a broadcaster. To...
I am trying to understand surface finishing of PCBs. In order to do so, can somebody tell me that what kind of surface finishing Nordic uses in boards like nrf51 - DK where...
Hello!
I am designing PCA10000 based PCB. Unfortunately my manufacturer can't make PCB using prepegs and cores that used in PCA10000 (4.4 and 4.8). They can make using 4...
Hi Nordic
After download SDK12.1.0, I want to extend DFU service in my application.But i find it different with the pervious versions.
For example, i can know how to...
Hi,
I have just started a new project in uVision, using the ble-app-template from the peripheral examples. its running on a custom PCB, with no 32Khz XTAL, and i have changed...
The user manual only tells information of pins , active low such things of led on nRF52832 Dk. There is no detail information of components on nRF 52832 DK board. So, can...
After reading the FAQ on DFU I still do not understand how the bootloader and SD DFU are performed so that a failure during the upgrade does not brick the device (see answer...
Hi,
I have some queries about ESB RF Communications.
1.The address : is it possible change RF communication to one node(Tx) to multiple nodes(Rx). If Yes, Where can...
Hello,
I found that after using SPIM I have forever additional over consumption (additional 400-500uA).
It was solved here in forum
And there is errata 89
[edit]...
I use Gazell to acomplish one host --two device.When i just have one device,everything is OK。But when added to two,it cannot work.
I think,whether channel of two devices...
Hi, I am looking for the test report on the bluetooth emission of the NRF52832 that we use in our product. Could you send it to me by email? Thanks,
Emeline