Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi everybody,
I'm having a problem with the advertising function of the SoftDevice.
When the application starts advertising the function "sd_ble_gap_adv_start()" returns...
I have 3 devices that can communicate via UART: 1) nRF52840-DK (PCA10056) 2) FTDI (set to 5v logic) 3) BLE HM-19
I'm using the example in ./nRF5_SDK_16/nRF5SDK160098a08e2...
Hi,
In gps sample, the prj.conf file is:
And I can use Putty or Serial.app (on my Mac) to view the output
In our application the prj.conf file is the following:
...
nrfjprog is reporting "Cannot connect to J-Link." while trying to erase on MacOS Catalina
Board used to work properly, but attempting to re-connect after a wipe of my MacBook...
I am using the nRF52840 dongle (pca1009).
I have read from some digital inputs successfully, but am not able to read from P0.02.
I set it up as an input with the following...
I am new to BLE and this question may seems little unusual.
My goal is to connect two nrf52 together over BLE and when i press a button in central device , a write event...
Hi!
My goal is to sample an ADC channel with 10 kHz sampling rate and acquire 2000 samples in one samples acquistion and then return to lowest possible power state. This...
Hi,
I received a Thingy91 from a colleague who orderd it shortly after hitting the virtual stores but didn't do a lot with it. I got it on my table and started to work on...
Hello,
SDK 15.3.0
s140
nrf52840-DK
IDE: SES
I am attempting to use the LPComp + NRFX TIMER 4 to count the rising edge of a signal, the timer is being used to time...
I am currently evaluating the nrf52840 for a possible future application which is based around BLE and should also provide a HID Generic interface to perform communication...
hi..I have merged the saadc with ble_app_uart and i have added all the respective files and enabled the ppi, saadc everything . while i am running the code ,getting unknown...
Hi,
I noticed something strange while developing with the nRF9160 modem's RTC. Here's the sequence of events
Connect cellular
Get time from NTP server and initialize...
Hello nordic
I'm running iot icmp example on my nrf52832.
The border router is Rapberry 4. root@raspberrypi:/home/pi# uname -a Linux raspberrypi 4.19.71-rt24-v7l+ #2 SMP...
Hi Nordic Support,
I am not getting sensor(VL53l0X) value,i used slave device address=0x29 and register address=0x01. I am getting starting distance value=255,afterwards...
Hello ,
I am trying to send 1,000 of MPU-9250 data from NRF5832 peripheral(ble_nus_uart) to NRF52832 central(ble_app_uart_c).
And i have been searched this site and...
