Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello!
I am dealing with nrf52832. I want to process data reception with SPI during f_write processing. Is this possible? As multi-thread processing 1) PT_THREAD in pt...
I'm developing a wearable device using nRF52832. I am developing OTA-DFU nowadays. I have successfully tested the buttonless OTA-DFU using the nRF52-DK.
And I'm testing...
Hi, I have a nRF9160 and I am currently working with the gps example: ncs\nrf\samples\nrf9160\gps
When I run the example, I only see
all the time. I went out on a big...
Hello,
i am struggling with the implementation of i2s to use it one SK6812 Leds.
To start with i used this https://github.com/cheehieu/nrf52-sk6812-led-driver example...
Hi All,
I study this post to enable long-range(s=8) on ble_app_blinky ( nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_blinky )
In the post, one of the settings...
Hello,
I was able to program the mesh experimental dimming example(server) into the external nRF52832 module using the debug out pins on the nRF52 DK.
The programming...
Hi,, I'm trying to set a recv timeout on a UDP socket (coap) using setsockopt() and getting an EPERM error. I've tried the setsockopt() call both before and after the (successful...
I'm attempting to use AWS IoT Just In TIme Provisioning(JITP), but no luck. Any help.
I tested JITP on my account, not Nordic one, with local mosuqitto client on Mac and...
I'm trying to use aws_fota, but it doesn't work. Any help?
I was able to set a job on AWS IoT, but the download job doesn't start. The job status is always "in progress...
Hello
I am writing a peripheral emulator application on android. My peripherals include 2 services and 4 characteristics. I tested my application with nRF Connect on the...
Hello All,
I am working on nrf52810 board
Using sdk 14.2
I am trying to modify some bytes of advertising packet .
I am referring the previous post as link given...
I'm getting ERROR 12 upon calling ble_advertising_init. I understand that this is caused by exceeding the advertising packet max payload of 31 bytes. What options do I have...
Hi All,
I am testing the performance of a Relay Node in a mesh network.However it seems don't work.
I would like to show that the Relay node operation such as Rx and Re...