i have the nrf5833 dk board, i just started programming from quick start and it worked two times and now it does not program at all, programming failed
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hello,
I'm using low power comparator with cross detection.
It works but I can't detect if it's failling or rising edge.
Can we detect simultaneously DOWN and UP...
Hi,Everyone! Now i have the board nrf52832 and i'm trying to get the battery value and send by using saadc.
i have read the example of ble_app_proximity and saadc,and i configure...
Hello! I compiled hex file with NRF52_BOOT in mbed cli. It was programmed successfully. Mbed os version include fix to use nrf52 DFUService. Bootloader is loading correctly...
Hi Nordic guys,
we are observing a strange behavior. Here some background on the project:
we are developing a peripheral device that asks via L2CAP signalling connection...
Hi,
I would like to know, whether it is possible to use a TCXO with single output as a LFCLK source, i.e. connecting the TCXO output only to XL1, instead of connecting an...
Hello everyone, I encounter a question. I follow below link to solve the issue.
https://devzone.nordicsemi.com/question/104118/adding-pwm-to-ble_template/
I've set the...
We are currently porting our proprietary stack from the nRF51 to the nRF52.
To save on BOM we are using an external 20ppm 32Mhz crystal to synthesize a 32Khz clock (power...
Hello,
I have develop an android application which connects to BLE device and perform read and write operation, so for this i was using Android-nRF-UART .
But my application...
In the release notes for the IOT SDK (which as the MQTT examples) it says: "Once BLE link is disconnected, lwIP example applications no longer get a global prefix. The only...
Hello all,
I am new to ARM architecture with some prior experience in Arduino based application development and some FPGA experience. I have a few queries:
Should...
I'm developing a project based on the Nordik UART Service and I wouldn't use pairing as in the example.
However I have some problem when a central device is already connected...
We're targetting the nRF51822 and use the pc-ble-driver (via connectivity_1.1.0_115k2_with_s130_2.0.1 )
Currently I'm using the dev board and the virtual COM port connection...
Hello,
I am trying to move from ARM Compiler v5.06 to v6.4, but I encounter an error, which I cannot handle.
The project builds fine with v5.06. When changing to v6...
Hi;
I am trying to secure DFU OTA. For that, i am using SDK12.2.0 and done with example file.
Now how to generate this .dat file itself.
Also explain each parameter...
