I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Is there any way to print all SDK documents at once?
I'd like to print all of the SDK v12.0 Documents and carry it with in offline,
But I can hardly find any PDF Document...
Hi.
I'm trying to figure out how to properly use GPIO pins, but so far I did not find a document explaining how to use GPIO with nrf included functions.
I found bits and...
I am using nRF51 (PCA10028) DK and nRF51 SDK v9.0.0 for Development. I want to merge all three DFU(BLE + SERIAL + ANT). i have merge BLE and SERIAL DFU code. For this i have...
Hi,
I merged 3 hex files(softdevice.hex, bootloader.hex, application.hex)
I uploaded this hex file to nrf52382 DK.
After uploading hex file to DK, although there...
Hai
i have the following queries about pairing / bonding in nrf51822.
can i retrieve the bonding information from flash memory. if so how can i do that..?
if a...
Hi
Last year I got a nRF52 devboard and I modified the ble uart peripheral example to flash a led depending on what it recieves from nRF uart app.
It all worked fine(after...
Hi,
I'm trying to use the SPI example from the SDK 11 to comunicate with a MPU accelerometer.
The first time it works well, but then the clock send only 8 peak, so the...
FIrst timer with the nordic.. so i could use some help.
i've tried my code on the eval kit and it worked fine. On my custom board (has external 16MHz crystal www.digikey...
I've come across a couple of products that shows up as both classic and BLE. But when connecting to these products via nRF Connect or inspecting the traffic, I can't seem...
From reading the reference manual, product specification as well as searching the developer zone: here and here . Is it correct that the AVDD pin supply's ONLY the radio....
I have a strange problem with the secure bootloader.
After a succsessful DFU update of firmware, the firmware starts, but resets after a short while (about a second). ...
Hi,
While I'm Flashing LED Blinking Example in nRF51822 Ek using Keil uVision 5 along with SDK v12.2.0 , Program is uploaded but LED is Continuously glowing without blinking...
Hi
I have been trying to make a dual bank serial dfu bootloader with security features for nrf51822 (board 10028), but seems the UART/HCI dfu support is missing in SDK...
