Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hello community
In the pin_change_int example the following code is written:
So, this basically means: whenever PIN_IN goes from low to high, the 'in_pin_handler'...
Hello,
There is a comment in the v1.1 manual (shown below) which states that the first capacitor in the matching network (C3 in the reference designs) shouldn't be connected...
Hi:
By our stack up at Z direction, there is a touch sensor FPC coil above nRF52840 and the gap is 0.65mm
And this coil will radiate about 1xMHz radiation
Will it impact...
Looking for different options for flashing/dumping program on custom nrf52832 pcb designed and used as BLE.
Has another full fledged MCU on PCB which handles all the peripherals...
ble_nus_data_send() can not work . SDK15.3.0. I have used two NRF52832. Based on the examples ble_app_gatts_c and ble_app_gatts,I have added nus service . Now central role...
I have my Thingy:91 working now but I can only see "terminal" data in nRF Connect for Cloud. I was expecting to see graphs of the data and a map when I have a GPS fix. The...
Hello everyone,
I am using light_switch server and client example from nrfmesh examples but nrfmesh ios application cant find nrf52 usb dongle.
I have changed pca10059...
I have developed USB firmware for the 840 based on the USBD example so that we can use WINUSB (WCID) for the host. The design is for USB 2.0 full speed with EPIN1 for device...
ble_nus_data_send() can not work . SDK15.3.0. I have used two NRF52832. Based on the examples ble_app_gatts_c and ble_app_gatts,I have added nus service . Now central role...
Somehow my account got deleted and so did my ticket. I had to re-register my account an i'm creating this ticket again:
nrf9160_pca10090ns.dts.pre.tmp:89.42-101.3: Warning...
Your served radio tramsmitter/receiver example using PCA 10000 USB dongle, PCA 10001 evaluation kit.
It's just only one byte data communication. It works well.
If I communication...
Hi, i'm trying to read an i2c sensor on interrupt. Doing it directly in the interrupt is apparantly bad, so io tried using app_sched_event_put, but that just crashes inside...
Hi,
I'm debugging a small app that is using the LPCOMP to trigger an interrupt when the BLE device is turned off. We have a capacitor to maintain alive the nRF for a while...
