Hi,
I am trying to build bluetooth hci_uart sample for esp32 board and haven't had much success so far. I am running this command to build:
`west build -p always -b...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
Hi, i am trying to send my notify characteristic every 100 msec, i am using timer for this and when i am connecting to the nrf app, my nordic device is sending the data but...
Hello,
Thanks for your reading.
I tried to read the CHIP_ID value(0xD1) of BMI160 in MetaWearCPro firmware using SPI.
But I could not get the correct value(0xD1). The read...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
My development Kit is official PCA10040, and SDK is SDK 11.
when i opened the keil project of ble_app_multirole_lesc int the examples of SDK with Keil MDK5.14 and compile...
Hi,
I've got a nice, well-documented bug here:
github.com/.../25
The short of it: Adding a single printf() statement to this mbed OS example causes my nRF51-DK board...
Hello all I am new Nordic and Bluetooth, before starting my project I did small experiment to understand the system i did the following steps.
Used nRF51822 -32 KB...
Hi all ,
I used SEGGER Embedded Studio v3.10 , and import a ble_app_uart keil project , but now build warnning as follow:
create .elf file have a warning "cannot find...
I'm using a nrf51422 customised board. I want to push the firmware to Bootloader mode via ANTware using a payload. But if i use graceful shutdown, the application malfunctions...
Hi, i used sdk11 and softdevice version s130_2.0.
And i used pwm library.
i try to make pwm pulse accurate 38khz.
When i used sdk 6.0, i could control timer used...
Starting SDK 11 (10?) DFU requires a zip file that is being generated with nrfutil.
To generate a package you need to supply a private key (generated by nrfutil as well)...
I have an existing working application running on a board with a Nordic Semiconductor NRF51822-QFAA CPU on it. The CPU is already programmed with (1) a SoftDevice S110 v6...
Hi,
Is it possible to use a different capacitor value, say 4.7uF instead of 1.0uF, in the DC/DC converter circuit on the nRF52832?
Kind regards,
Thiemo
Dear Nordic Team,
Thanks for support.
We have nrf51422 development kit and trained in this sample code. How to use the same example code for nrf51822. please support...
Hello,
I have been looking to program this IC, connecting via SWD with no luck. I can connect to the target but for some reason once i try to perform erase programming...
Hi
Is there any limitation to characteristic size for use in notifications?
The reason for asking is the following:
I have a service with a characteristic with size 24...
