Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Dear support team, we are trying to make the device ST IIS2DLPC (accelormeter) talk via SPI to the dev board PCA10040
We are using the evaluation board STEVAL-MKI191V1 wich...
Hello,
I am trying to build the lwm2m_client sample on my ubuntu 16.04 machine. I tried building for nrf9160_pca10090ns and nrf9160_pca20035ns The build fails with:
...
Hi,
I am using SEGGER/SEGGER Embedded Studio for ARM 4.12, I used Two working Examples ble_app_gatts_c_pca10040_s132 and flash_fstorage. I am getting these errors "undefined...
Hello,
For our project I'm using a LIS2DH (accelerometer) that is supposed to trigger an interrupt on its pin INT1 when a movement is detected.
I use nRF52832. Before...
Hi
I'm not familiar with C language, I tested the saadc example in SDK, it worked well in P0.02
But I dont see how they set CH[X].PSELP or CH[X].PSELN (V(p) and V(n))...
Hi
Using PCA 10040A , SDK 16.0.0 and Segger Studio.
I would like to generate a short accurate *** on a GPIO , probably 250 nano seconds duration. So I am looking at using...
Hello All,
my application should record acceleration data and time stamps.
After recording the data block from start to end should be transmitted.
I only know that...
Hello, guys.
In our current project, we need to periodically update AWS IoT Server with the data from local sensors. So far, thanks to the cloud_client example and your...
Hi
For a new project I'm looking for a cheap bluetooth chip. All my software resides in a PIC, because on PIC I have a lot of experience and I don't have the time to dedicate...
Hello all,
I am using NRF52840 and SDK 16 in central mode and added two UUID filters to the scan module for two different groups of peripherals . My application works fine...
Hi,
I am trying to send a test message in Server through mqtt and used the mqtt_simple example for that.
For the test I insert data_publish() function in main() like...
Hi!
The subject is most of the question.
I am beginning to customize the ble_app_template example, and when I build it, connect, and look at the advertising data, I see...
I want to connect NRF52840-pca10056 to PC via USB cable. I followed the docs but the OS doesn't detect the board automatically when plugged in. It only recognizes the board...
Dear Nordic Community We are about to develop a Testing-Framwork to compare different Mesh-Networks (Bluetooth Mesh vs. Thread vs. Zigbee) for which we would like to use the...
