I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi! I would like to power the DK through a external power bank. This leads to led5 blinking rapidly for a while and then turning off. I assume this is because of the debugger...
Hi Team,
We are trying to compile the code with my changes, that changes are normal changes only.
But we are getting below errors in "nrf52840.h" . But we didn't do...
I have a nrf51-DK, SDK 9.0, S110, dual-bank bootloader that supports both serial and ble protocols, developed using GCC/Eclipse. I'm able to flash my app/bootloader/softdevice...
We are building a sollution using nRF52832. Using the UART over BLE application example as a base we managed to add DFU capabilities to the application etc.
Right now I...
Dear NRF community and support This is a followup question to the DevZone post https://devzone.nordicsemi.com/f/nordic-q-a/2860/flashing-bootloader-and-application-via-j-link...
From everything I know and understand of the system architecture, this shouldn't be possible, but one of our early production units out in the fields has twice now apparently...
I'm designing a two-part computer input device: Part A will communicate with the computer over BLE, but it must also be able to forward along messages from Part B. Here's...
Hi,
I am trying to update the MTU between the central and peripheral to the maximum MTU.
at the connection interrupt from the central side I added
but I got error...
For nRF52832 I see in the datasheet:
I OFF_RAMOFF_GPIO System OFF, No RAM retention, Wake on GPIO,
While for nRF52840 only “System OFF, no RAM retention, wake on reset...
I have an iOS App which is just designed for updating our device firmware OTA. It uses the Nordic DFU library, updated to the latest cocoapod. It connects to our device, and...
Hi,
I use OpenWRT and nRF52832 to develop a BLE gateway, the nRF52832 connected to OenWRT through UART. Now,we need the uart serial DFU of nRF52832, and I found that nrfutil...
I am looking for some advice before diving in to what could be a big waste of time. In my existing Thread implementation, I use nRF52840's in two different configurations...
Hi all!
I am using mesh sdk v4.10 and sdk 16.0 with an nrf52840 custom hardware. I have a question regarding the mesh event handler. I am seeing something weird which I...
I am trying to run DHT sensor on the nrf9160 using the sample provided by zephyr (can be found under zephyr>samples>sensor>dht). The code was meant to run on nrf52. Is there...
