I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I'm building some code off of the twi_master_using_app_twi example which is available in the SDK (v11.0.0).
The two peripherals I'm working on are an accelerometer (LIS3DH...
I've just upgraded to Windows 10, and I've found that the PC freezes completely (i.e. no mouse movement, no keyboard response) when I unplug an nRF52 DK board. When I plug...
Hi,
In my application, I need 3 PWM to drive LED. Each PWM will have the same frequency but not the same duty cycle.
Is that possible to do that?
I know that Timer0 is...
hi
on android side of my project i try to disconnect from gatt by this code
mbluetoothGatt.disconnect();
but in nrf51422 this event not trigering
static void on_ble_evt...
Hello, I am working on low power modes and I got trouble finding the code to switch from NRF_POWER_MODE_CONSTLAT and NRF_POWER_MODE_LOWPWR. Can anyone please guide me to better...
Bonding causes power consumption to rise.
I have a central and peripheral device communicating using the nus-service. The peripheral device is running FreeRTOS with tickless...
Hi,
I'm trying to test the DFU over HCI included in the SDK examples but I can't make it work. This is all the information of the environment I'm using:
SDK: 10.0...
Condition: nRF52, SDK11,s132, SDS v2.0.
Using the sd_ble_gatts_hvx() in timer1 interrupt service(timer1 interrupt priority is set to level 3) will result in hardfault. While...
I am using SDK_11 s130. I am looking at app_error_fault_handler() in app_error_weak.c
Inside app_error_fault_handler(), there is this line of code;
UNUSED_VARIABLE(bsp_indication_set...
Hi,
I am using keil uvision 5.17, SD 130, nRF 51822, dualbank bootloader.
I have programmed own application and merged bootloader, application, soft device.
I...
I am using ble_app_gls on SDK_11 s130 on nRF51-dk.
This is a follow-up question to the question below.
devzone.nordicsemi.com/.../
After enabling debugging, I discovered...
Hi,
I'm using the example projects "ble_peripheral/ble_app_uart" "ble_central/ble_app_uart_c" in SDK10.0.0 to test data throughput.
I'm sending 20bytes of payload. But...
Hi,
I am using nrfjprog package installed in folder /opt/Nrfjprog. I am getting the fallowing error.
nrfjprog --eraseall
ERROR: JLinkARM.dll load failed. Try again...
Hi,
I've migrate from 3V to 1.8v power supply.
before the migration, using 3V power supply, DEC2 connected to 47nF directly to GND.
after the migration, using1.8V power...