I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Dear Sirs,
We are creating a solution based on your chip, but have heard that it is / might be discontinued.
If that is the case, what would be the replacement model...
Nordic SDK 15.3.0 ble_app_gls merge with custom service
Hello I am new on KEİL and NRF52832,
I am trying to merge this custom service and Ble_app_gls example . I added...
Hello
Would someone ,please reply to the below thread,waiting for the response
https://devzone.nordicsemi.com/f/nordic-q-a/60891/unable-to-read-the-128-bit-uuid-with-base...
Hello how are you?
I'm using the mesh example Light switch example from nRF5 SDK for Mesh v4.0.0. I implemented the RSSI util model and it is working, one question I have...
I am working on a new design and i am using ST7789 (240 X 320 pixels) screen with nRF52840, it is working fine. I have followed the code provided in SDK example (big thanks...
Hi,
I´m trying to add a new, custom TX characteristic to Softdevice. I use example from SDK 16 "UART/Serial Port Emulation over BLE".
How I can do this, is explained...
Hi,
I flashed and run "ble_app_uart" example on nrf52833 DK. With an UART tool, I can recieve data from smartphone (rx characteristic) but I can´t send data from UART tool...
The sdk 16 - bootloader positions s140 softdevice V. 7.0.1 wrongly so that it is acknowledged as Application and does not work with nrf52840.
As you can see at the picture...
Is there a place to make suggestions for new releases of nRF5 SDK's or even contribute?
I've been using the current USBD CDC ACM library and needed to modify the app_usbd_cdc_acm...
Hi , I am making a zigbee application to write attribute on remote node. Please share the application structure to implement writing functionality of attribute on remote node...
Hi,
I am trying to test PSM settings on the nRF9160 using a custom PCB. I have set the active time to 3 minutes with a periodic TAU time of 10 minutes.
When the device...
I’m developing an application based on pc-ble-driver to talk to an nRF52840-based dongle (from Fanstel).
I’m having trouble disconnecting cleanly when a connection has operations...
Hi,
I´m using the NRF52810 device and have an issue with the SAADC peripheral.
I basically have 2 channel where i want to do some averaging to improve noise.
The setup...
