Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
In my application I am using Multiple App timers. Is there a way to prioritise these timers. Are there any draw backs in using multiple timers in "ble app".
Regards...
I want to set the resolvable private address ( RPA ) manually instead of letting softdevice do it. I went through documentation but I am not sure about it. I know that I can...
Hi
I am trying to put nrf52 device to system off mode, and wake up by button press.
If I do not enable the softdevice everything works fine, and button press wakes up...
Hi, I am trying to use the nRF52 to pass IMU information through BLE to a smartphone. We have a custom chip with the nRF52 and LSM9DS1 on the same board. I am able to program...
Hi!
Friday I can load the binary into PCA10040 (blinky example) ands works well. But today I load de binary but not works, nothing happen.
I'm used this example /Nordic...
It seems that I configured LFCLKSRC correctly, and advertising led flashes correctly.
Can I make any troubleshooting codes for Radio or Antenna?
Can I make some codes...
Hello,
Is it possible to erase only first N kB of internal flash memory before reprogramming nRF51 with JLink?
Lets say that I just want to erase first 64 kB of flash...
Github said it works in sdk8.1, But I place it under *nRF51_SDK_10.0.0_dc26b5e\examples* It works well in the demo board. Question,Can it be used in sdk10?
What I want to...
Hi,
referring to the SoftDevice Specification, S132 Softdevice vx.0, paragraph 15.2 (Attribute table size) I wonder how one does work out the size of the attribute table...
Hi,
Hope this is not a duplicate post. I am using nRF52832 and SDK Ver 11 and am facing the following issue:
After configuring the UART and SPI, I put a string e.g....
Hi
Today I have recieved the new nRF52 Development kit PCA10040. I have downloaded the latest version of SDK nRF5_SDK_12.0.0_12f24da working with ANT_s212_nrf52_2.0.0....
I can't build ble_app_proximity_pca10040 example due to uv5 core size limit. One user suggested that I port the old device_manager to SDK 12 proximity example to reduce core...
Hi guys,
I am using the nRF52 DK with IAR 7.70.2 and SKD12.0.0.
I notice that the blinky example has 2 versions for the nRF52 DK:
a) blinky_pca10040...
Hello,
my problem is that after changing the UUID service and number characteristics in my nordic device, the nrf connect app on ios8.2 not recognize it (in the android it...
