Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
There is a comment in the v1.1 manual (shown below) which states that the first capacitor in the matching network (C3 in the reference designs) shouldn't be connected...
Hi:
By our stack up at Z direction, there is a touch sensor FPC coil above nRF52840 and the gap is 0.65mm
And this coil will radiate about 1xMHz radiation
Will it impact...
Looking for different options for flashing/dumping program on custom nrf52832 pcb designed and used as BLE.
Has another full fledged MCU on PCB which handles all the peripherals...
ble_nus_data_send() can not work . SDK15.3.0. I have used two NRF52832. Based on the examples ble_app_gatts_c and ble_app_gatts,I have added nus service . Now central role...
I have my Thingy:91 working now but I can only see "terminal" data in nRF Connect for Cloud. I was expecting to see graphs of the data and a map when I have a GPS fix. The...
Hello everyone,
I am using light_switch server and client example from nrfmesh examples but nrfmesh ios application cant find nrf52 usb dongle.
I have changed pca10059...
I have developed USB firmware for the 840 based on the USBD example so that we can use WINUSB (WCID) for the host. The design is for USB 2.0 full speed with EPIN1 for device...
ble_nus_data_send() can not work . SDK15.3.0. I have used two NRF52832. Based on the examples ble_app_gatts_c and ble_app_gatts,I have added nus service . Now central role...
Somehow my account got deleted and so did my ticket. I had to re-register my account an i'm creating this ticket again:
nrf9160_pca10090ns.dts.pre.tmp:89.42-101.3: Warning...
Your served radio tramsmitter/receiver example using PCA 10000 USB dongle, PCA 10001 evaluation kit.
It's just only one byte data communication. It works well.
If I communication...
Hi, i'm trying to read an i2c sensor on interrupt. Doing it directly in the interrupt is apparantly bad, so io tried using app_sched_event_put, but that just crashes inside...
Hi,
I'm debugging a small app that is using the LPCOMP to trigger an interrupt when the BLE device is turned off. We have a capacitor to maintain alive the nRF for a while...
Hello,
I am trying to use the nRF9160 DK to publish some sensor data to an Azure IoT Hub. I have been able to successfully connect to the mqtt broker and publish simple...
