Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hey,
I am using SDK16 and want to update the bootloader on my NRF52840 from SDK15 with a new one.
I modified the bootloader from SDK16 a little bit. Then I created a Zip...
To the kind attention of Nordic support team,
I have got in here two pictures of flash. The first one it is after installing bootloader and settings, softdevice and application...
Hi,
I am working on a product development that uses an nRF52832 (through a LAIRD BL-652 module).
We have a voltage point (named 5V), that is connected to SIO_28 GPIO through...
Dear,
I used ncs_v1.0.0_joakim to adapt the battery of my thingy91:
I used: battery_monitor_read(); to read the %battery, and it worked well
I just updated new...
I understand correctly that in order to use my private key for my applications, I must first sign an immutable bootloader with this key and upload it to the device?
I used...
Hello there,
It seems the CC310 backend for ChaChaPoly does not allow zero-length data or adata (associated data). I am implementing a protocol that requires this (Wireguard...
I am trying to change the default ATT_MTU size from 23 to 64.
my code uses Ble_nus service and Eddystone_Service.
Eddystone service is in connectable mode and it's where...
Env.: nRF52 customBoard, SES, nRF5_SDK_16.0.0_98a08e2
Hi,
I'am working with ble_app_template example and currently trying, to merge it with the experimental multiperipheral...
I have added an external SPI flash on the nRF9160 DK board, and wired it up to SPI3. I want to partition the flash into two ares for separate uses, but the partition_manager...
Hello.
I have just recived my nrf5340 PDK. I started with the hear rate example programming with the console. With some troubles but finally it worked.
Now I'm trying...
Hey nordic ,
I am doing project on BLE. I am Using Segger embedded studio v4.30b. (Board pca10040).
In that I am using features like advertising ,scanning and connect...
nrf52840 SoftDevice V6.1.0 release-notes written, The scanner and initiator roles can now be configured to receive ADV_EXT_IND PDUs on both 1M and Coded PHY, using a single...
Hi,
I'm using nrf52840 DK to connect and receive usbhid message with the message size > 64 bytes (examples 343 bytes), so the message is divided to multi packages. I modified...
I am trying to build the nrf9160 from segger studio. I have installed and expoerted path of zypher and gnuarm toolchain gcc-arm-none-eabi-8-2019-q3-update-linux
I am getting...
I'm trying to run SDK examples on BL652 module from Laird (which is basically nRF52832) by means of debugger from nRF52 Dev Kit
Strange thing is that all examples (even...
