Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
There seems to be an issue when reading GPIO pins returning false readings. I am using two pins for I2C communication, 26 and 27, I am configuring them with the required configuration...
Hi Everyone,
I am developing a device that needs to record data from ADC onto a onboard NAND memory.
Following the USB MSC example for NRF52840, it seems like the device...
Hi,
I'm working on the nRF52840 DK and running the ble_app_uart example.
I'm connecting to the BLE using the nRF UART V2.0 app and open a terminal.
In the terminal I'm...
Hi, I am trying to connect the GPS module with the nrf52840, and the development kit reads the GPS information via UART, I wonder if there are any examples? I read the example...
Hi everyone !!!
I want to know, is Nordic going to make its Mesh demonstration at CES18 public? I didn't attend it but I'm interested in their demonstration and what tools...
How to write a byte in flash by using
static void flash_word_write(uint32_t * p_address, uint32_t value) function
while in a advertising mode.
I tried to call the...
Hello.
Here is my conditations;
using ukeil 5.
sd132 Version 5.
sdk version 14,2,17b948a
In my project, i am using secure connection. So peer manager...
Hello Guys,
I am newbie to nrf51822 programming. Currently using nrf51822 (raytac's MDBT40) with S130, SDK11.
I am programming the nrf51822 using arduino IDE using this...
Hi,
I'm seeing this error PM_EVT_PEER_DATA_UPDATE_FAILED sometimes and I need to understand what are the options on handling this error except for just asserting it. I...
Hi,
We have to implement a nRF to nRF DFU. On the nRF51 side a have an external memory with two bankers to perform secure update and downgrade using a bank 2. Now, we are...
when scan the BLE device, screen can look the device's name, but the time parameter is means?
ex:
-31 dbm <-> 1010ms
1010ms means? is about dbm power value>
thks...
We have field reports of BlackBerry Priv not being able to "connect" to our nRF52 based hardware.
BlackBerry Priv is: www.gsmarena.com/blackberry_priv-7587.php
(Runs...
I use same SDK to program the 1.nRF52_DK borad (on broad chip 52832) ,and 2.external program borad chip 52832.
Have a issue, 1.nRF52_DK borad is success to advertisement...
Hey!
Using osx, SES 3.30, importing experimental_ble_app_blinky example from nRF5_SDK_11.0.0_89a8197 to be used with NRF51822 chip. When importing I chose pca10028/s130/iar...