If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi There,
I'm just getting started with ARM and the NRF52832. I've done a lot of work with 8-bit micros and I'm interested in learning 32-bit and in porting some old AVR...
I would like to use printf using ITM for debugging my application using a BL652 module (nRf52832).
I have followed the instructions in the Keil paper APNT_308. Printf is...
hi,
i am doing a project where i have to merge nrf mesh light switch server with mesh dfu example. i am using nrf mesh sdk v1.0.0 and nrf52832 mcu.
i have merged two programs...
I want to disable logging (which is working OK). In my app.config.h I have set the following:
#undef NRF_LOG_ENABLED
#define NRF_LOG_BACKEND_SERIAL_USES_UART 0
#define...
Desired behavior:
After a long press of the button, my desired behavior is to erase bonds and advertise and let another central pair and bond to the device.
After a normal...
Simultaneously, as a way of a parallel bus, using an extra one as a input clock, and save the byte in easydma, without CPU intervention?
Either in the nRF52832 or nRF52840...
Are there any options today that include Sub GHz, Bluetooth, and LTE for Mesh Networks??
I am thinking of a Gateway with multiple sensors communicating through Sub 1Ghz...
Hello,
We are trying to evaluate the HomeKit SDK with our nRF52832 BLE modules. The "Lock(static)" sample application doesn't work with Apple 'Home' App on iPhone 8+. The...
I'm currently evaluating different platforms, that run on the nrf52832 soc, like Nordic Semiconductors own firmware, as well as Zephyr, myNewt and mBed. As you guys from ...
Dear sirs
Good evening !
I´m using the RF24.h library in order to develop a system that comunicates in peer-to-peer mode.
When I transmit 3 bytes towards a receiver...
I'm hoping someone can tell me if I'm on the right track. Do I understand correctly that on an nrf51, the LPCOMP can be configured to wake the processor on an analog input...
Hello,
I was wondering how is calcualted or read on the Thingy firmware the variable w for the quaternion used in the Gyroscope readings.
Looking into m_motion.c in the...
The power data of lfclk is measured under the same hardware and software conditions. When we used two model chips, we found a difference of 1 microamps for the value of the...
hi, I am trying to make buttonless dfu working, but I am not sure how to do that. I am using SDK 14.2.0 with nrf52832. right now, the ble dfu example works. and I found in...
hi
i am using nrf52 dk with MPU 9255 as slave.which pin number of nrf52 dk should i use for 4 wire as SDA, ADO, SCL, NCS.In the attached file ,it is given as p0.20(MOSI...
