Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello, we would like to consider this chip for a product, but I have been waiting for this to be on sale for purchase since February 2017. It's still 12 weeks out and it's...
Hi, I followed the NRF51 Guide and downloaded the file linked, and it installed the J- Link Commander, once opened it gives a prompt J-Link> and when I enter in -e command...
Hi guys,
I’m using nrf51822, s130 and sdk 12.3.0…
I would like to achieve that unknown peripheral won’t find my product or at least differentiate by device name while...
Can i use the bouder router used in thread example(on nrf52840) in the iot example to replace the Rpi bouder router so i can skip the tunnel setup(using hurricane tunnel)...
Hi everyone,
I have some questions regarding the use of EDIV and Rand in BLE Legacy Pairing.
What I understood from the specs is that these are generated during...
I think instead of releasing separate SDK for #BluetoothMesh, Nordic Semiconductor should merge #BluetoothMesh into #SoftDevice. Is it possible ?
If yes, then we can even...
We are using the nrf52840 with OPENTHREAD and would like to use the Nordic COAP application because block transfer and observe are implemented. We need to do multicast and...
Hi,
I have a development board nRF52832 and we are looking for 3rd party modules built on the same. I want some configuration changes on the modules.So, please someone help...
Hi
I am currently using SDK 12.1.0 with SD 3.0.0.
I want to add the option for serial DFU, which was added in SDK 13.0.0.
I wonder if I can implement the serial bootloader...
first of all many many thanks for nrf sniffer 2.0 and all of it's improvements (linux, live data display, easy install ... etc)
i'm sure there are still a lot details missing...
I am trying to use the nRF Connect v1.0 RC with the pca10040 board. I followed the instructions of your [page] and when i open the serial port i got an error (Error occurred...
I am using nrf52832_xxaa with SDK v11.0.I tried writing into the APPROTECT register by using the code below
sd_softdevice_disable();
NRF_NVMC->CONFIG = (NVMC_CONFIG_WEN_Wen...
Hi, as per subject, I would like to know the trade-offs of using the internal DCDC vs LDO when it comes to RX sensitivity specific to the nRF52840-QIAABB variant.
From this...
Hello,
I am using the nRF840 PDK for testing the radio communication.
During my tests, for TXPOWER=0xD8(at minimum), I found a gap of 7 dBm between the radio output...
Hi, I am trying to connect the nrf52840 to GPS module, and I hope that the dk could read the GPS information via UART. I try to modify from this example nRF5_SDK_14.2.0_17b948a...
