Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I'd like to run the DK in at the lowest power in SYSTEM_ON mode.
It's my understanding that the ble_app_gzll example places the system in the "low power" SYSTEM_ON mode...
Hello Folks
I would highly apprciate if anyone can point me in the right direction here
After lot of consultation we imported a smal size shipment (of about 1000 nRF51822...
Connection_mode_with_1sec_Notification.jpg
In my BLE project I am using connected mode, and I found that the current consumption is very high ~190uA during idle mode. I...
I'm currently working with an own hardware with a nRF52840. We had some time to get the radio working, because we copied the schematic of the PDK. In the reference design...
Hello I am using sdk version 14.0 and softdevice S332. I am looking at the ANT + bsc code. I have two questions when looking at this code.
bsc_tx could not see an event...
Hello guys,
Please help me on this.
I want to erase BMD 350 chip using BMD 300 erase and recovery software tool. But I can not do it.Error comes as per the attachment...
Dear all,
I want to create a star network, composed by one gateway and a limited number of nodes. The nodes periodically send information to the gateway. I am using the...
I'm running the HID Keyboard example from SDK 12.2.0 on nRF51-DK with SD 130.
When I long push Button1, it disconnects for a moment and connects again immediately.
Events...
I am trying to make a custom application in which I need to connect to a device and read/write its characteristics' value.
But my target device has had 4 primary services...
Hi Nordic Engineers!
we bought 110 nRF52840 IC's for Field tests.
10 of them marked Q1AAAA / 1716AK
another 100 marked Q1AABB / 1745AC
What is difference between series...
Dear Nordic Team,
Thanks for supporting.
Now i am work with secure dfu using SDK12.3.0.
My Hardware :PCA10028
nrfutil version 3.1.0
Create Zip file like : nrfutil...
Hello.
I want to design a product. It will have these features;
It has 4 buttons on it.
Obviously it is battery powered device.
I want to see some information...
Hi
I have made ble scanner using nrf52 and I have set uart baud rate 921600 and sending scanned beacon to other micro-controller for processing but It does not scanning...
Hi
I'm looking for an example on how to write a hex-file to SoC using nrfjprog.dll.
The P/Invokes are all set and working fine.
I'm absolutely not familiar with python...
Hello,
In our project we want use a large characteristic with notification property.
I use a " ble_app_template " project from nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral...
