Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
Hello,
I have some trouble to use the Secure Bootloader example, which comes with the
nRF5_SDK_12.1.0
I installed the latest nrfutil and hexmerge. I can compile the...
This piece of code appears in all IoT SDK examples:
eui48_t ipv6_medium_eui48;
err_code = ipv6_medium_eui48_get(m_ipv6_medium.ipv6_medium_instance_id,
&ipv6_medium_eui48...
Hi, I am using the nrf uart app to communicate with a smart phone and the NRF52. I am trying to detect whenever it is sent a value between 0 and 60 from the phone, and save...
Hi,
I'm working on nRF51822 with SDK 11.0.0 softdevice s130
I have an nRF module acting as central and smartphones (iOS and Android) acting as peripheral.
I tested...
Hello, what is the BLE max range w/out usin PCB antenna?
And what range ll be if i reducing the connection interval down to the minimum 7.5ms, set Tx power to +4dBm using...
I am using the nrf51822-QFAC-R in an application where the realization of the antenna is very challenging, and I expect to have an antenna |S11|=-1dB, with variations of the...
Hello, I want to clear things up a bit, all these concepts are starting to overwhelm me somehow. I want to know:
What can have UUID and handle? I understand that profiles...
I want to use ATMEGA 328 to send a packet over to the chip as follows:
SPDR = packet ;
Can some one kindly post what the content of this packat should be ?
is it possible...
hi,
i am working on FDS. here i am able to write number of records and also able to read them back.
but while updating i deleted one of the old record and writing new...
Hello,
I have some problems with UART communication with my nRF51 DK.
When I connect it through USB cable, all is ok. But when I connect pins: P0.09(TXD), P0.11(RXD) to...
Hello, i have a question.
Can nRF51822(s120) handle more than one connection at same time?
Let me explain: i have one server(nRF51), and two(or more) clients(nRF51 and mobile...
I've got an application that does a lot of nRF51822 GPIO wiggling and the timing needs to be controlled. In one spot I simply set a pin high then low like this:
nrf_gpio_cfg_output...
As shown in title, I am using the ubuntu 14.04 in virtualbox.
When I connect the Nordic 51822 development kit to my PC, I can only detect the serial number of this device...
keil uvision
Hello. I don't know how to get away from the warning "last line of file ends without a newline".
I added new line, but nothing change. It happened with my own...
Dear Sir,
Here I would like to disable the Adversting idle power down dynamically but in some situation it will fail.
The APP_ADV_TIMEOUT_IN_SECONDS is 180 seconds as...
