Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
Hello,
I need to know does nordic S120 stack gives the RSSI value on receiving data from peripheral? Currently I am able to get the peripheral RSSI on peripheral device...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
The Nordic UART code was built for the UARTE using the following definitions:
#define UART0_CONFIG_USE_EASY_DMA true
#define UART_EASY_DMA_SUPPORT 1
#define UART_LEGACY_SUPPORT...
I add my own codes in nRF51-ble-bcast-mesh-sdk-8-support project,
then I find that if device_flash_init() is compile to this project,
the program cannot finish rbc_mesh_init...
Hi,
I have app + bootloader in one packet. On Android nRF Toolbox both can be updated in one step using Distribution Packet option. Is this possible on iOS?
I know it...
The BLE Central tutorial (S130 based) does not connect to my peripheral. My peripheral connects fine to the Android MCP and the 128-bit service UUID is what I expect.
I...
I use nrfgo studio to program the hex file. but I have only 128kb of flash and the softdevice took 88kb which left less then 50kb. I have a hex file of 70kb
my question is...
hello.
I develope the using the Nrf51822, bootloader and application not using softdevice llbrary.
the procedure is that one mcu send the mrf51822 by uart. and mrf51822...
Now I have generated bootloader.hex used by /DFU/bootloader.
After programming bootloader.hex and s110_nrf51_8.0.0.hex,the device's name changed to DfuTarg.
But when I...
Hell,
Wich BT dongle I can use to dawnload data fro board with nRF51822 chip on it?
If thear is App. to use for comunication and dawnloading data from electronic board with...
Hi,
I am using nRF51422 with s130 soft device along with SDK v9.0. I am trying to read/write flash memory using pstorage module. I am using BLE nus service for data transfer...
each time I start my program (nrf51 device) I get an error code I save in flash to check it at next restart. I can read error code 0x20
is this a correct error code and what...
Hi,
I try to generate a PWM signal on PCA10040 with the nRF52832. To do that I copied the code from the Product Specification into my application, but nothing comes out....
Hi,
I made my prototype board using the nrf51822 chip. for this prototype i use an on-board connector + external programmer to flash the nrf51822 chip.
that's work...