Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
nRF52840 OPS 0.5.1 lists the following highlighted sensitivity spec:
The Bluetooth core spec defines sensitivity for this payload length as a BER of 0.017%, not 0.01...
Hi
We are trying a Nrf51-Dongle in a school prosject here in Norway We need to use one of the GPIO pins on the Nrf51-dongle as input When this input is 1 , we want the dongle...
Hi ,I am using nrf52 DK with mpu9255.I am using source code given here here .of this link,I have taken 'nrf5-ble-data-ready-interrupts' example .code builts fine in keil v5...
Using nrf51422 in KEIL. I am verrrryyyy new to this type of programming. I have been looking at multiple examples within the nortic github to find how to input analog reading...
I started Heart Rate Monitor app "ble_app_hrs_pca10040_s132" on nRF52 evaluation kit (nRF52832). Everything work well when I connect with nRF evaluation kit from Android devices...
Hi!
I just got my PCB with a Telit BlueMod+S42 Module on it (nRF52832).
I' using the LESC feature and ist works properly on the PCA1004 and on the Telit DevKit (same Module...
Hello,
I'm working on a bootloader based on the example of SDK13.1. I want to add two more characteristics to the DFU service, but after I add them, the nRF Connect app...
When I use sdk14.2 nRF52810 ble_nus_string_send to send data to a mobile phone android, the first connection is no problem, but disconnected again after connecting problems...
Dear friends,
If i set the conection interval=100ms and the slave latency=1, the slave will wake up every 200ms. If the slave has data to send, it will still wake up every...
I haven't been able to find a drawing file for the nRF51 Development Kit. Is there one out there?
Ideally, I'd like to get the drawing and a *.STP file for SolidWorks.
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
The file nRF5_SDK_1 4.2.0_17b948a/components/libraries/util/app_error_weak.c requires the following modification to correctly compile: Add: #include "app_util_platform.h"...
Hi,
I'm currently using SDK v14.2.0 and I'm attempting to merge the buttonless DFU bluetooth example into the bluetooth template project within the Eclipse Oxygen environment...
Hey Guys,
I have 3 tasks running on FreeRTOS, SDK v14.0.0. In each task, I want to use SEGGER_RTT_printf() to debug.
I currently just call SEGGER_RTT_printf() without...
I have two nrf devices nrf51822 and nrf52DK, In nrf51822 i'm using S110 and i had created a custom service with 10 characteristics. If i connected to nrf connect i can able...
