I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
hi
I am trying to gather information on what is needed to create a mesh network using BLE.
I am more familiar with Zigbee/Thread, but I am asked to implement something...
I downloaded S212 for nRF52 from thisisant.com and programmed the softdevice to nRF52832DK(PCA10040) via nRFgo Studio. Then I copied the 'include' folder of unzipped softdevice...
I have been trying nrf-sniffer with no success. Setup is:
Win7 64,
Sniffer Win 1.0.1,
Wireshark 1.10.14 (both win32 and 64 tried),
PCA10000 and PCA10001
The sniffer...
I generally upload codes from mbed.org to my PC then send the hex file to nRF51822 by nRF51-DK's pins. But I don't want to use cables to upload hex codes to nRF51822. Are...
Hi community,
When I want to use the example multilink peripheral inside the s120 directory example of the SDK 6.1.0, I'm not able to compile the code.
The device_manager_peripheral...
So, I want to make an application where my NRF52 advertises an URL via the Eddystone beacon.
The URL will link to an webpage, that will connect to my device through the physical...
As here said link1 If we want to use flash in the mesh we should ignore APP_ERROR_CHECK(NRF_ERROR_INVALID_STATE) in ts_sd_event_handler() ,
2.And here link2 tell us...
How do I set up a variable length characteristic which is greater than 20 bytes and use notifications with this characteristic?
For example I have several variable length...
In an nRF51-based application I'm working on, I am using the SPIS peripheral and a generated clock signal to send a large buffer out over serial using DMA. I want to use the...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
hi
in tutoriall service beginer there is
static void advertising_init(void)
{
uint32_t err_code;
ble_advdata_t advdata;
// Build advertising data struct to pass...
wireshark 2.0.3 which is what got installed when I downloaded it is not supported according to the nFsniffer program.
So what, and how do you set this up?
I am using a function to read the die temperature data from nRF51822 as follows:
static uint32_t temperature_data_get(void)
{
int32_t temp;
uint32_t err_code;
...
Hi all,
my Setup :
nrf51822 QFAC Build Code A1,Waveshare Core51822 Board
keil microvision
nrf device family Pack 8.6
without Softdevice erased with openocd...
