hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hello
I am still relatively new to microcontroller development with the NRF52 DK. I am currently running a modified version of ble_app_uart__saadc_timer_driven__scan_mode...
I have a Taiyo Yuden Evaluation board , with EBSHJNZXZ completed with Segger and j - link , when load the project in board, not have any error debug, the sketch is load successfully...
I am following this tutorial
I'm using Segger Embedded Studio v3.10i, and SDK 12.2.0. I have the exact same problem in both Linux and Windows.
I have done everything...
What are the details of internal pin connection circuitry when connected as GPIO/IRQ vs ADC vs Comparator? Is there an internal pull down (what value)? Is there internal diode...
what should be RAM Settings for 51822QFAA chip?
I am using nrf sdk for mesh. what should be required ram settings for 51822 in order to run light switch server example....
Hello,
I have problem with missing GPIOTE event. Sometimes event doesn't occur, sometimes there is no problem. This event is very rare but important. I think it happens...
Hi all,
I am working on Temperature and Humidity(DHT11) with nrf52832, After advertising the Bluetooth i am calling the DHT11 sensor function in loop, few seconds it is...
Hello , I would like to know lifetime expectancy of NRF52832 IC. By lifetime expectancy I mean the amount of duration before NRF52832 goes non-functional. Please help me in...
Hi,
In disk_uninitialize function there are following lines of code:
if (m_drives[drv].last_result == NRF_BLOCK_DEV_RESULT_SUCCESS) { m_drives[drv].state |= STA_NOINIT;...
I have extend the light switch example to send message to the other node. I have refer This example to send message. But how to configure another node to receive the message...
HTU21D.rar hello there i am interfacing HTU21D with nrf51822. i am reading temperature and humidty from HTU21D. humidty register is E5. and temperature register is E3. now...
Hi,
I was trying to implement software UART for our product so I decided to use timer compare channels event connected to gpiote with interrupt. I want to toggle data line...
Hi,
Application: turning on/off a LED by toggling a GPIO pin using a timer and PPI. Important: the on-time of the LED must be very precise, i.e. the jitter must be minimal...
Dear Sir/Madam,
I have a sensor prototype board using nRF51822 for Bluetooth communication and I am now working on its firmware. I have installed MDK version 5.16 and...
Dear sir,
Sir i am using MDBT42V module. I want to know that whether the SCL & SDA pine are internally pulled high in this module ?
Regards,
Manoj Hiwarkar
