I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hey everyone. I am having an issue reading the WHO_AM_I register from the stm lsm6dsv16x. I am using the spi1 configuration as shown in the academy classes. I have very short...
I am using an nRF52840 USB dongle to sniff some Zigbee packets for a product I am developing. I am trying to use Wireshark to decode the messages shared. I followed the steps...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
Hi, I am using the nrf54L15DK to take some current measurements. I am using the PPk2, connected to P6 on the DK, supplying 3V, and have the USB on the DK connected. With a...
Reference states a +/- 3% tolerance, which is rather high. 1. Do any of the reference voltages exhibit a better tolerance? 2. Is it possible to roughly model the tolerance...
Hello Nordic team,
After many hours I have not been able to get socket dispatching working with Zephyrs MQTT client, and I am not sure how to proceed.
First of all I would...
Hi, We’re trying to develop a way to create fully self-contained repositories that include:
-the toolchain
-the entire SDK
-the necessary tools (for example, flashing...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
Hello,
I just got nRF54L15 DK and Im getting this error when flashing it:
Im running on a mac, have NRF Connect installed along the command line and 2.8-2.9 sdk...
I wanted to know if this program starts sending advertisements using the Coded PHY OR if it starts advertising in the normal advertising channels using the normal 1Meg output...
LE audio can support multiple stream, but I can't find any description about following application, please advise....thanks
phone1 use unicast to play audio on headphone1...
Hello, I'm trying to use BLE on nrf52833. I'm developping with segger embedded studio and I' m usign the BLE peripheral example "ble_app_blinky". Firstly I erased the flash...
Hello, I want to build serial_lte_modem sample for a custom board based on nRF9151, but it fails with this error:
error: Aborting due to Kconfig warnings
I can build...
Dear,
I recently upgraded my project from NCS 2.4.0 to NCS 2.9.0 and encountered an issue with the ST7789V display driver.
Previously, I used SPI0 to interface with the...