I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hi,
I have a custom board someone designed with two SPI masters and one I2C master. We're now trying to enable the second SPI master and I'm running into errors because...
Hi all,
I am working on FOTA, my set up is with SDK15. I have followed the steps for DFU and i have used the secure_bootloader example, the thing is working fine, i can...
hi i have attached my gps+gsm module with nrf51 development kit and while reading an out put i wont be able to see any output , even with out put i dont know to to do debugging...
Hi,
I have completed all steps in the example at the following link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader and all...
I am developing hardware for the nRF52840. After testing our firmware, we are going to need somewhere around 6,000-7,000 mAh to run our hardware for the time needed. We were...
Hi, all.
I used sd_ble_gap_addr_get() function to get a MAC address in the different example and the result was different.
I tested this example in SDK v14.2 and v15...
Hi,
The amount of information and reference documents available about Bluetooth qualification is overwhelming. It would be great if someone with this experience sheds some...
Do nRF8001 chip has its own internal linear regulator? or Does it need an external like the module created by Adafruit ( https://cdn-learn.adafruit.com/assets/assets/000/035...
Good evening all,
I'm trying to get my DK52 communicating with a CR95HF (this is a NFC controller with serial and SPI control interfaces), I'm using a breakout board - BM019...
Hi Sir, I use load switch circuit to control nrf8001's power. I found even the vcc of nrf8001 is empty, nrf8001 still works. That's not my expected result, I think nrf8001...
Hi ,
We know that the nRF8001 use the random static device address . I have the questions below :
A. Will the device get one new address after power on ? or is the address...
Hi,
I need to exchange data between 2 ble modules.
I'm using SKD 15.0.0 and first ble module is nRF52840, second ble module (esp32) acts as GATT server.
I have full...
Hi, I am trying to make nrf52832 as a UART certal. The service UUID and characteristic UUID of peripheral are shown as the following picture. They are all 128bit and quite...
I'm attempting to implement a simple, GPIO driven interrupt system using SDK15, but I can't seem to find any examples using the nrfx_gpiote driver, or documentation on how...
