When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Ok I’m new to ARM / Nordic and Bluetooth but after a bunch of reading I downloaded SES and the Mesh SDK and got the light switch demo to both compile and run on a few boards...
I'm looking for where the compiler is for the nRF52832....
I just need to compile code, and copy the binary to the device....do you have any pages which show, step by...
hai. I got thingy 52 from Nordic tech tour. now i would like to reconfigure it. for enabling all its sensor into RTOS(real-time operating system apache mynewt) with the nrf52...
I want to implement a ready line for SPI and I noticed nordic has similar code in your sdk: components/serialization/common/transport/ser_phy/ser_phy_spi_slave.c.
However...
Hi,
I am trying to send data to server using ESP8266 WiFi module interface with nRF52832 DK board via UART interface. My problem is when i sent AT command to ESP8266 it...
Hi,
I have a project with 52810, I met below build error when compiling dfu project:
.\_build\nrf52832_xxaa_s132.axf: Error: L6366E: uECC.c.o attributes are not compatible...
Hi
Now I'm using nRF52810 base on SDK v14.1 and I want to do the OTA for it. When I combile the bootloader project, I get so many error "No space in execution regions....
I just want to change the Advertising interval min and max values in ble_gap.h file in meta wear RG
so do I have to change firmware code or is there any other way to deal...
In the eclipse setup here
https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/development-with-gcc-and-eclipse
It give two links to example eclipse projects...
I can see that we can use APPROTECT to disable reading of the flash.
This seems to be reversible using: nrfjprog -f NRF52 --recover, which will erase the flash and allow...
I used SDK nRF5_SDK_14.1.0_1dda907.
I added cycling speed and cadence service of BLE and bicycle speed and cadence of ANT+ in ble_ant_app_hrm example of multiprotocol. ...
First - thanks to those who answered my question about the Segger Embedded Studio code size limit. It appears to have be fixed when I switch the build configuration from ...
I would like to use a Bluetooth protocol analyzer for sniffing traffic in my Mesh network. I need to input the devkey(s), netkey, and appkey to the protocol analyzer software...
Hi,
I am adapting the uart example to send mensages between central and peripheral using JSON. In this moment I can send central <------>peripheral...
I have a problem...
