I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I have question about signal names in datasheet nRF52840.
On the pins B19 and T2 on page 14 both pins have the same initial signal names (P0.11).
Please send me...
Hello,
I would like to add the ST7735 driver from the nRF5_SDK to the Mesh SDK along with the necessary components (SPI,..). I copied the entire components directory to...
How is the health model supposed to work?
I'm currently doing some tests with the light switch example and I don't really understand the different roles of the nodes in the...
Hello,
I have some trouble to write/read data in flash region,
I am using FICR region to save data,
if trying the command : nrfjprog --memrd 0x10000010 --n 0x10
I...
Hello All
I am using an SOC which has nrf51822. I am trying the blinky example with the softdevice. When I debug the code, the code first enters the SystemInit function...
Hello Nordic devzone,
I'm using Mesh SDK and nrf52PDK, and i'm using light_switch example.
could you please let me know that if it is possible to broadcast a message from...
Hi Experts:
I met one complier error as blow. Would you get me some idea? High appreciate!
--------------------------------------------------------
Ubuntu 16 (64 bit...
Hi
I am porting another nRF52840 SPI OLED driver based on nRF5_SDK_14.2.0_17b948a\examples\peripheral\spi_master_using_nrf_spi_mngr
At first, it works fine without button...
hi guys ;
i have already an application on android phone that can read and write charchtéristic i also followed the tutorial Bluetooth low energy Characteristics, a beginner...
Hello
I am using nrf51822 .The function of DFU has worked well,but some weird problems puzzle me.
1、After DFU is successful,what is nrf51822's working state? Does it reset...
When I just plug the USB cable on the board I get a GPIO high voltage of 3V. But when I also put +5V on the external supply pins, the GPIO high voltages are 4.5 V. Is this...
Hi,
We are using nrf52832 board with sdk14.0. We are facing two issues:
Our use case is to send the data continuously when the notification is enable and stop...
The Bluetooth pairing is not working properly. I am developing the Application based on Bluetooth pairing with UART. Here I have included my concept and Program.Help me out...
Hi to everyone!
I have been getting the output of NRF_LOG_INFO functions through RTT in J-Link RTT Viewer terminal. The code has been executing in nRF52832DK.
Now I...
I have set up an nrf cloud and can control the led on pca10056 using the nrfcloud so configuring the gpio(pin no 7(Port P0.7))is becoming a problem.Can u provide me with a...
