I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
Hi, we are planning to use npm1300 for charging a battery, but we will have a limitation on the power supply (VBUS in npm1300 naming convention): the capability of making...
I'm trying to understand latency between simple events (like a button press) and transmissions to show that event on the nRF Toolbox iOS app. In some trials, my updates are...
Hi we are developing a customized Bluetooth smart PCB with the nrf51822, I load the softdevice 110 v 7.1.0 no problem, but when I load the heart rate demo app it stuck in...
I would like to modificate the LED Button application example. The LED characteristic should stay as it is, only the Button characteristic should be changed. I want to use...
Hi,
I have used several Bluetooth Low Energy solutions and I looked into several examples and something is missing. What I miss is to prevent pairing. It is something quite...
In SDK source code of S110 SOftdevice, I'v found two events for which module is registered and waiting using "softdevice_sys_evt_handler_set" & "softdevice_ble_evt_handler_set...
Hi,
I'm working on getting our product through BLE certification and they are asking a few quesion's that I'm not sure about.
1: Pairing. Is it using a fixed PIN or...
Hi,
Routine running normally in low power mode with power_manage() .
but after sd_flash_write/erase current consumption goes high(almost 20mA).
If anything is missing...
Hello,
i want to update the softdevice S310 V1.0.0 to version V2.0.1. My applicatio based on SDK 6.1. With S310 V1.0.0 all works fine. But i can't update to S310 V2.0.1...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hello, I have a problem with GPIO Input control
My sensor work on special clock generated by MCU
I've controlled this sensor by Arduino like this
//SCK digital pin...
We are using the NR51422 to develop a BLE application. We reused the project “ble_app_hrm” from the SDK v6 and ran it using the NRF6310 board, everything is ok.
We just...
Hello Everyone, right now i use nrf51-dev kit and i want blinky code for that, in Keil i compile code and load in kit and it work fine but now i want to make code in eclipse...
I'm trying to debug the blinky example with SDK 7.1 using Eclipse Luna. Going through several threads here I could figure out configurations needed and build the app. I can...
Hi,
I have been trying to study how to implement support for over-the-air (OTA) updates in my current S110-based project. But I'm already stuck in the very beginning. How...
I am using softdevice and RTX at the same time.
RTX is using RTC1, softdevice is using RTC0, so no problem there.
But sd_softdevice_enable require a clock source as one...
