void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
Im trying to use this example to send serial data from GPS module via BLE:
github.com/.../ble_app_uart_low_power_slave
I have disabled hardware flow control since...
Hi
I tried gateway and LED_mesh examples. It worked well. But, I found some issues as below.
When I tired MCP windows application on laptop with PCA10031 dongle...
Hi there,
I am using the nrfjprog to flash the nrf51822 via a J-Tag programmer. Here is the command I used in the command prompt:
nrfjprog --eraseall --programs softdevice...
Haw can I configure ble_app_ uart examples for bonding using? I want to connecting, transmit and receive data throw the UART only with 5 fixed devices.
Hi,
I updated to softdevice 8.00 recently, and found something different with softdevice 6.00.
When trying to program the new softdevice hex to the chip using nrfgo studio...
Hi,
I am using nRF51822 chip.
I am using the softdevice s120_nrf51_2.1.0. On top of that i am flashing the HRM central example given in the SDK nRF51_SDK_8.1.0_b6ed55f...
Hello, I'm fairly new are Nordic and have inherited a good project from a departing coworker. We are using Keil uVision 5+nRF51822+BLES110 softdevice.
She explained her...
Hello,
As mentioned title, when using printf with softdevice, "Stopped by a vector catch" occurred.
I am using my custom board(nRF51822 and s110).
And I am using IAR...
Hello,
When i try to set value of the gpregret using sd_power_gpregret_set and clear functions in on_write callback function, cpu gets stuck (i check it in debug mode). Can...
Hello
I'm trying to communicate with an sensor over the TWI HW interface during a BLE connection with the S110 soft-device, and every time I try to use the TWI bus the...
Greetings,
There is a bit of strange operation in UARTE peripheral in nrf52832 with the DK. In the simple code below, if both of the if statements with comments 'Check 1...
Hello everyone,
I have a strange issue with s110 + whitelisting + Device Manager + nrf51822 + GCC and hopefully you can help me with a good advice. It appears that the...
hi,
I am trying to integrate buttonless switch to boot loader as explained in the documentation and the hrs experimental example.
I am working on SDK7.2.0 and using...
