Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am having trouble with the service discovery of my application. When I click Discover Services it takes several seconds to discover all of the services. For example between...
Hello!
I have a problem with ble DFU application upgrade. I use the Master Control Panel 3.10.0.14 under Win 7 on virtual machine and nordic ble usb dongle.
On the firmware...
I used AdaFruit Bluetooth LE shield previously that uses nRF8001. I can define new customer service using nRFgo studio (which only supports nRF8001). I am moving towards using...
Hi,
I am using pca10040 board. i need to toggle a led in 5sec once. I tried to change the prescale value. But im not able to get that much time delay.
Can any one help...
SDK Version: nrf51_iot_sdk_0.8.0_f1f6187
In SDK all examples are given for PCA10028. Is it possible to run on PCA10001?
What I have done so far with PCA10001:
1.Programmed...
Hello,
I have modified the Android-nRF-Blinky Application to use it with the Datathroughput Demo on the nRF52 DK.
The android application runs on a Nexus 9 with android...
Hi, i try to understand how to use mode for supply voltage measurement. But i have a problem and i get always 1.225 volt
hal_adc_set_input_channel(HAL_INP_VDD2_3);
hal_adc_set_reference...
Hey all,
Wondering if we could use an external 65.536KHz LF clock, or thereabouts, instead of the 32.768KHz? We need better resolution for the RTC, but don't want to turn...
hello im from mexico, last week i order 10 NRF24LE1 and arrived the next wake,
but before i have many cuestion about.
someone can tell me that the burner can work?
compiler...
I had a mbed firmware running on a ST Nucleo 64 that periodically query a sensor for data. It only use the I2C, a button interrupt and a LED for heartbeat. I ported it to...
Hi,
I want to know that if the TWI easyDMA in nRF52 can help in achieving this task:
we want to read from TWI each 10msec based on a timer interrupt and write...
Hello:
I have detected a problem with a timer on my program.
I can solve it, but I would like to understand what is happening exactly.
My program starts to scan BLE signal...
I'm writing the client-side code for the Nordic DFU service and according to the spec, the DFU packet characteristic uses Write Without Request. Are there any examples of...
