hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi, I'm using trying to use the DFU via BLE, dual bank example from SDK 8.1.1 (with SD 8.0.0) and got it all working up to the point where I call "activate image and reset...
Hi,
I have a problem that the ANCS keeps resetting my board, so I was able to reproduce the problem on the PCA 10028 dev board.
Conditions:
iOS 8.x or 9.x
No...
Hello,
I am running Windows 10, nRFgo Studio 1.21.1 and Keil uvision 5.16a.
I was doing some tests with my nRF51 DK board, like loading the beacon example found in the...
Hello,
I am using simple_adc__pca10028 from 8.0.0 SDK to read values from my sensor, its a kind of tensometer. My configurations are:
NRF_ADC_CONFIG_RES_10BIT...
Dear sir,
I am using your NRF24L01+ chipset with STM32F407ZET6 controller for 2.4GHZ RFID communication. can u please share the STACK for this controller.
I have a few questions (using nRF51 DK and/or external nRF51822)
I use an analog pin to measure the voltage of a capacitor of an analog circuit. From time to time...
Hello,
I would like to implement HID over GATT profile (BLE) in the Beaglebone Black (BBB). The BBB will be used to interface with a laptop/computer running Windows 10...
Sorry for this long message. I am new and quite lost.
I just purchased a nRF51 DK and installed nRFGo Studio, Keil MDK and NRF51 SDK. With nRFGo, I programmed the Segger...
Hi,
I'm trying to link the static esb library (esb_gcc.a) with the mbed toolchain. Everthing seems fine until the last stage of the linking phase where my actual functions...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
I have inserted the USB dongle nRF24LU1p in to PC. In nRFgo studio, it is detected as nRF24LU1+ Bootloader. If I click on the bootloader, It shows a window from where, it...
Hi,
I've got the following error when trying to update the softdevice and bootloader on my iPad:
Error on StartDFU Message:Data Size Exceeds
I've carried out the...
Hello!
Do I need any extra passives, connecting SD card to SPIM of nRF51?
It works fine with MOSI, MISO, SCK, SEL, VCC and GND directly connected, just want to be sure it...
