I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi,
I made simple command shell via UART. It works fine when I type commands in terminal by hand. But I run into troubles when BLE chip is fed from MCU that send characters...
When I connect my ble mouse to the PC win8.1 , media button works normal.
When I power off and power on my mouse, it reconnected to win8.1 PC quickly, sensor ,left button...
I'm using the nRFgo motherboard (nRF6310 together with the PCA10004 Cpu board. I'd configured the nRF51822's Uart to 1 MBaud).
Is the RS232 level shifter (which is part of...
It's this will be work?
// Initialize the Bond Manager.
bond_init_data.flash_page_num_bond = FLASH_PAGE_BOND;
bond_init_data.flash_page_num_sys_attr = FLASH_PAGE_SYS_ATTR;...
Hello：
I need to ask you after the next programmed into how this routine testing 。（nrf51_sdk_v4_4_2_3355\nrf51822\Board\nrf6310\ble\ble_app_alert_notification ） The iphone...
Dear Developer Zone,
I am working with nRF51822 and IOS.
My device can only be connected to one central, so to one iPhone. To refuse connection from others centrals...
Hi all,
I've got some questions about the DFU OTA Nordic example (nRFToolbox):
What is available full stack update or profile update?
Firmware flow, does it need to...
Hi Folks,
I'm running into a problem with the pipes on my nRF8001. After I issue a Connect (0x0F) command, I receive:
CommandResponseEvent (0x84)
ConnectedEvent...
We have setup the RX and TX modes for ANT+ in Advanced Burst mode.
The setter function works (can confirm that by using sd_ant_adv_burst_config_set());
However when...
Hello,
I understand that S310 stack currently supports Ant+ and BLE peripheral. Is there any way to incorporate BLE central (S120) and Ant+ (S210) stacks on the same device...
Hi,
I have nexus 4 smart phone with nRF Master Control Panel application. How can i change the IO capability of the master device? I need to test the pairing process (passkey...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi There,
We are using two microprocessors in our project is kind of activity tracker which is stm32l (M3) with accelerometer, temprature sensor and SPI flash connected...
I'd like to start developing with the nRF51822, and have found the two kits supplied by Nordic, the nRF51822 Evaluation Kit and the nRF51822 Development Kit. What's the difference...
