Hello Nordic Team,
I have a working project that uses BLE to communicate with a mobile app, and I am now looking to integrate Google Fast Pair as an additional feature....
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
The example DFU project (dual_bank_ble_s110) for NRF51422 seems to work just fine on my custom board that has NRF51822. Is there a problem to use it like that if I set the...
Dear community,
I'd like to report a problem on the Direct Test Mode software provided in nrf51 SDK v6.1.0.
In this mode, 2-bytes commands are transmitted over the serial...
Whenever I try to run the following Convolution function for the 12th time in my code, the Processor is halted and I get the following Error on console:
Performing single...
According to this example, the device should be advertising RX and TX Characteristics. I also believe that when I connect to the UART app using my iphone, I should be able...
I have been successfully using my nRF52 Dev Kit (PCA10040) for the last few days. Today, when messing around with the UART drivers, I seem to have messed up the JLink-OB....
Hello,
I have an NRF51822 beacon board and two small 0.96" OLED displays (does not matter for me which one o use). One with GND, VDD, D0, D1, REST, D/C, CS and VCC pins...
I'm on windows 8 using the 1.0.1 sniffer application and wire shark 1.10.14 64bit with a Nordic nrf51 dongle. I'm using an nrf51 dev board with ble_peripherals/ble_app_blinky...
with nrf51 there is 2 blocks (block0 for softdevcie and block1 for user data and stack). I configured the system to retain RAM before going down using sd_power_ramon_set(0x00030003...
Hi,
I have a device that is configured to work in GAP central role. This device only scans for specific advertisements from specific devices. Could you suggest how I can...
Hi!
I used the develop board test the application "ble_app_multilink_central" and "ble_app_multilink_peripheral",but it is always connected failed,and disconnect Reason 0x0008...
Hi there. I have a very long C code that is running correctly on Code:Blocks, Ubuntu Terminal ( using GCC ), Eclipse and on Dev-C++.
However, when I put in on the board...
Hello,
I've been trying to control MCP23017 IO expander with TWI using nRF52832. When I execute the code it stops at nrf_drv_twi_tx. The address pins A(0:2) are 0.
Any...
I have having following configuration:
I want a fail safe method to update firmware on nrf51822 using attached host controller. I looked at serial wire debug interface...
Hello,
I'm running a serialized application based on the SDK 10 and S130 v1 and I am in the process of porting the peer manager to the application µC.
Due to the fact...
