I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
We're using nRF51822 and in the future we'll use nRF52832.
We do use bluetooth, but as far as I know, we don't use encryption (code is based on the HRS example, and...
Is nrf52 support 3 wire spi interface? I am using AD9837 3-wire spi module act as slave and nrf52 dk act as master. I am using SCLK, SSn(i.e.,Fsync) & MOSI pins only.I want...
Hi, I’m a newbie of nRF SoC. I have a BLE gadget with nRF51822_xxAC that controls LEDs and obtains data from accelerometers through I2C(TWI) devices. The hex file for the...
Hello,
I am able to get NRFtoolbox dfu code work for iOS 10.3. and now able to perform the DFU on BLE device.
But when I perform the DFU its GAP name changes from Beam...
Hi
I migrated from SDK11 to SDK12/13.
In SDK11 I already had avaiable a softdevice to use for ble_app_uart peripheral.
In the new SDK I have to build the softdevice but...
I'm trying to understand example "ble_app_hts" how after advertising make a connection. I didn't see in code any call of function "sd_ble_gap_connect" ? how is made connection...
I use the nRF OpenMesh from the GitHub. ( https://github.com/NordicSemiconductor/nRF51-ble-bcast-mesh )
My mesh network just has two mesh node, node A and B.
I made A...
Hi everyone!
I want to work with two UART interfaces in my nRF52DK, in one hand, I must receive data sended by one cable which converts USB to serial, for this I use this...
Hello,
I caused a hardfault error and triggered the HardFault_Handler in "hardfault_handler_gcc.c". But instead seeint its source, I could only see the message no source...
When I start the nRF51822 sniffer ble-sniffer_win_1.0.1_1111_Sniffer.exe I get the following message:
!!Your firmware is outdated!!
Please upgrade (press CTRL-R).
When...
Hi team,
I am using sdk 12.1.0 and ble_app_hrs_c example.I enabled #define NRF_LOG_USES_TIMESTAMP 0 to 1 and iam usng nrf51822 dongle.my program gets hanged.I need to print...
Hi all,
I use the example of examples/ble_central/ble_app_multilink_central/ to test the connect timeout event. When it scan the peripheral and try to connect it, power off...
Hi, I am wondering why, sometimes, I get an odd packet out of order on the receiver. It is very random, it can occur at anytime, though usually it takes a minute or two. Testing...
So, does anyone have practical advice for reducing the code size of peer_manager and related modules, so that the ble_app_template project fits on the nrf51822 128KB part...
