Hello
I'm using an external flash to store large files, but I’d also like to use the SMP service to exchange small files over BLE. For that reason, I want to create a LittleFS...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi all,
I recently bought an nrf52840DK, and yesterday I tried to program an external board through the p20 connector on the DK with the SWD pins. I was able to flash the...
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi
I don't have the board space for a loop antenna, so I'd like to use a dipole. What sort of RF output / matching stage do I need for this on the nRF905?
Thanks!
Hello
I wrote the program by referring the some examples after compiling the program GPIO pin becomes high immediately (3.3V ) bu my aim is to make the GPIO pin as output...
I have two nrf24l01+ modules communicating on a single channel. The "remote" does 99% of the data transmission while the "base" receives and uploads to a host. Occasionally...
How to use stlink or CMSIS - DAP downloading S110 protocol stack? Jlink can use nrfgostuide down s110 protocol stack, i want to know how to use stlink or CMSIS - DAP download...
Hello,
Is there any information on current consumption for the nRF51822 when running the micro-esb examples? I'm curious as to how much current is being used in a situation...
I'm testing a custom board I did. The board has this 16Mh crystal
geyer-electronic.de/.../GEYER-KX-7_01.pdf
The CL of the crystal is 12 pF. I'm using a pair of capacitors...
Hi,
I am trying to get the ble uart example from the sdk 0.9.2 working on my nrf52 DK board.
But the nRF UART v2.0 application on my android phone, quits instantly after...
Hello,
I'm looking to send a 32 bits word to the example "LebButtonDemo", using an iPhone application created with Evothingd Studio (it uses Javascript).
I'm able to...
Hello
at the moment I have a running S120 BLE firmware update on my nRF51822 hardware.
This works fine on my desk.
But we have the additional requirement to update the...
Hi
I have an custom board which uses an nrf51422 SOC. I am facing issues with my radio.I use an softdevice s110 with an application on it.
The code just works fine with...
Hi Noedic,
I triggered the DFU function through APP, the device restarted and the base service UUID changed from 0x0001(nus function) to 0x1530(dfu function), but it is...
Hello,
I am working on S120 SD v2.1.0 for central and S110 v8.0 SD for peripheral and SDK9.0 and I am able to configure 1 single uuid on central and connect to multiple peripherals...
Hi.
I would like to konw some ditails aboute nRF9E5 device:
What is the rang between 2 devices using 433 mhz.
do you have any samples codes ? i need to trasmitt...
Hello,
After i disable SD i try to count ticks on TIMER1 from RTC1 via PPI.
Timer1 is configured property but TASK_COUNT don't increment cc.
I see that event TICK on...
