I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
I'm looking to design power management circuit for a 3.7V Li rechargeable battery powered wearable sensor design. Any such reference design would be greatly helpful!
Thank...
I'm developing a device that's supposed to establish an encrypted connection with an Android device and I've gotten PM_CONN_SEC_ERROR_PIN_OR_KEY_MISSING during connecting...
I have the Type 4 Tag sample application running and I can read and write the tag without any problems.
I'm getting a little confused reading through the sample application...
Hello,
I am working with the GPIO tasks and events feature on my nRF52832 DK. And I noticed some strange behaviour. I want that two Pins will toggle if some timer events...
Hi,
Please help me with the following theoretical situation:
I have a NRF52832 running HID profile, mostly sleeping.
From time to time, an external interrupt occur (GPIO...
Hi,
I am trying to get the data written from a central (a smartphone in my case) to one of the characteristic of my peripheral using write request. The problem is that...
Dear developers,
We had a working application with SDK11 SD2.0.1 that we have migrated to SDK12 SD3.0.0. With SDK11 we could successfully bond to multiple peripherals and...
Hi. I use the nRF51882 and Arduino ide for developing. My main goal is turn on and off the Led thru the Bluetooth interface. But when I use the UART service for it I have...
I am seemingly haunted by spurious 'soft resets' I cannot seem to find a good explanation.
I have an application that is to be dormant until activated. When waking up I...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hi, Nordic
I download SDK13.0.0-1.alpha_055eef3, open project
\gzll\experimental\gzp_dynamic_pairing\device\pca10040\blank\arm5_no_packs\gzll_dynamic_pairing_device_pca10040...
Is there any example of changing the default mtu size of 23 to a bigger value?
We tried increasing the att_mtu to 512, and reserved more ram for the softdevice, but still...
I have a rather unique problem. I want to control an "old-fashioned" DPDT relay using nRF52 GPIO lines. I'm trying to accomplish this task without adding a power transistor...
Hi all,
there is a nice section in here already about enabling the Reset input (P0.21). Unfortunately the link to the relevant infocenter docu is missing.
Could you...
