Hi There,
I am using a nRF52840DK board to experiment with NFC Tag technology.
I started with the "Writable_ndef" example inside the nRFConnect, and it works.
I wrote...
Where can I obtain the security certificates (e.g., client certificate/private key) needed for TLS authentication with nRF Cloud? - Are these generated during device onboarding...
I plan to use my own SIM card (not from Ibasis). Could you clarify how to register the device in nRF Cloud to enable A-GPS services? - Should I link the device’s IMEI or ICCID...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
I am using the minimal port referenced in this question: devzone.nordicsemi.com/.../
to interface the nRF8001 using an MSP430 device. I am currently in the process of porting...
I am using SPI MASTER example from sdk 7.2.0 with softdevice s110(using spi along with BLE).
In my program I have a requirement of reconfiguring spi pins after using spi...
I see that driver version 1.0.0 was tagged on ghitub: github.com/.../v1.0.0
However, when I visit this page: www.nordicsemi.com/.../38649 , I can only find the 0.5.0 version...
Hi
I use nRF51422 for our products.
In a product line, we check the CWtest mode current consumption current.
I decided the determination value of the CWtest mode current...
Hi.
I'm using nRF51822, S130, SDK10.0.0.
I made a source code as below refering radio_test which is in SDK examples.
But the width of frequency is just 0.2MHz as below...
hi,
so i was coding my program with keil and it reach the 32kb so i had to move to the free IDE Eclipse. for that i followed this tutorial devzone.nordicsemi.com/.../
...
Hi !
I've seen that the Makefile given with the examples changed a lot between SDK11 and SDK12, lots of improvements ! However there's still something I don't get. Why...
What system resources are required when using GPIOTE channels (not the PORT event, the other channels)?
I remember on the nrf51822 there was a long-running PAN, fixed in...
I programmed nRF51822 with S120 softdevice and ble_app_hrs_c application to scan beacons.
It works fine but have one problem.
It scans beacons for about 10 seconds...
hi,
i am working on ble_app_uart_simple_adc example which is referred from the link github.com/.../nrf51-ADC-examples
i flashed the code successfully. and detecting the...
Running the SDK11 example \examples\peripheral\twi_sensor on a NRF52 PCA10040 version dev board and can't get any output from TWI pins. Leaving pins unconnected and using...
Hi,
I am trying to set up the development tools for the NRF52 on my Mac by following this tutorial aaroneiche.com/.../
I am getting the following error when i try to...
Hi
I want to get external acceleration sensor values with SPIM using easyDMA on the sensor interruption (using GPIOTE). then after getting all data, I want to calculate...
Hello,
I have question, I'm actually developing an Android application and try to update the firmware on a device with a DFU process. It work on every mobile device except...
I am using the nrf51422 with softdevice 5144_2.0.1 ,
I set two network number using the "sd_ant_network_address_set" api , network number 0 for ANT+ cadence/heardrate.. network...