Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Do I need to manually go though every HW exaple in the examples in sdk12 and cut and paste all the little bits that I need or is there any other way?
I have a custom board...
Hi,
I'm using the nRF52 as a master and an external RF chip as a slave. After configuring my spi bus using nrf_drv_spi_init(&spi, NULL, NULL), in my main loop, how do I...
I have used nRF toolbox to update bootloader and firmware to my nordic device. I was previously using iOS9 (I believe 9.3.5 - whatever the latest version was before iOS10...
Firstly,I used ios9.3.5 to DFU successfully,
But when 9.14(ios10 was pushed),then my iphone6s was updated to ios10,
finally DFU failed.
The device can enter in the DFU...
Given this answer , do the BLE_GAP_CONN_SEC_MODE_SET family of macros only relate to the Write permissions of the device name?
Maybe a better way to ask this is: Is it...
Hi,
I am referring nRF5 SDK for Eddystone ( github.com/.../nrf5-sdk-for-eddystone) .
Here GCC Makefile based projects are scheduled for a future release.
I am trying...
Hello,
sorry for the dumb question but do you know which software does Nordic use for creating/editing sequence charts like the one in the documentation?
infocenter...
Hello,
I am currently working with NRF openmesh but when I try to set a new handle i get an error. This is what I tried.
uint8_t ledje = 0x01;
rbc_mesh_value_handle_t...
Hello,
I am doing bluetooth transceiving test. About in 10 times of transceiving wtih App, I got 9 times success, but one time failure. From my observation, App and bluetooth...
I evaluating nrf52_dk board, to build an application with custom BT Service on the nrf52_dk using the mbed platform. I see the new platform nrf52_dk platform is available...
Hi!,
I'm working in a Android app to communicate with a nRF52/nRF51 boards.
I've been using Bluetooth Smart nRF51822 Beacon Kit.
But I think what I need is not possible...
How do I change the properties of the Generic Access service's "Device Name" characteristic to be Read Only, not Read and Write? I see this
BLE_GAP_CONN_SEC_MODE_SET_OPEN...
Hi,
We are sending data every connection interval which is a stream using the API sd_ble_gattc_write. Whenever there is a dropped packet from what we understand, the Softdevice...
I used SDK11, SD332, and no change anything.
the application reset as picture.
can you test this issue and give suggest ,why app reset?
D:\work\nordic\BLE\SDK\nRF5_SDK_11...
I need a code example (e.g. Health Thermometer) that runs on the Beacon Kit. I have tried several combinations of soft devices and code examples, but I can't get it running...