I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
My application:
I have a peripheral (S110) that registers important alerts and immediately broadcasts them to any central that is listening. There will be some amount ...
Everyone.
Do you use nrf_drv_adc when using nRF 52832's ADC?
Or are you controlling the ADC directly?
I am not good at nrf_drv_adc.
Is this justice?
Please tell us your...
Hi, I was setting my new computer and installed nRF5x-Command-Line-Tools-Win32 V9.2.1.
Then open nRFgo studio it requests an update with strong recommended. After the update...
When my program was running,An error occurred.The program ran here
（app_error_handler_bare）and the error_info is
0x00000004, how can I find out the reason of error_info...
Hello,
I was trying to build Clapp oscillator with a JFET J310 (FYI: link text )as it is shown in the figure.
Capacitor C is variable and goes from 20 pF to 285 pF...
Hello
Please tell me about sd_ble_gatts_value_get ().
Please tell me about sd_ble_gatts_value_set ().
For these two cases, it is not used in the SDK, but is it old?
Please...
Hello together,
I' am working on a Bluetooth application and have a problem with the transmitting time of the Bluetooth.
In this Screenshot you can see the end of...
Hi,
I want to connect an ADXL362 low-power accelerometer to a nRF51DK via SPI for a BLE application. However, I'm still quite unfamiliar with Nordic Semi's BLE offering...
In SDK12.2 init timer user APP_TIMER_APPSH_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE, true);
but when I want to use more timer,how can i add the number?
Dear Nordic,
I am having some apparent delays in the time that passes from the pressing of a button, and the execution of the ISR that this button triggers. I am using...
Hi， Nordic
I checked DFU operation, found DFU work in bootload mode.
I want to know below operation is OK or not. Plz help me check:
download DFU bootloader
download...
Hi, I use the PCA10040 v1.1.
This is an example of a PCB stack-up.
My questions are,
In the case of PCA10040, which is 4 layered, what are the values of...
Hi,
I am writing a firmware for one of my custom boards which use GPIOTE to detect interrupt for 3 GPIOs inputs (P0.03, P0.06 and P0.09, both with internal pull-ups) and...
Hello,
I'm trying to write my ADC samples over spi on a sd card (Using SAADC like in the sdk 12 example with PPI and using fatfs like in the example in the sdk).
I open...
