Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
I have NRF51822 module with custom carrier board.
I trying the experimental ble app blinky (S130) with PCA10040 (master cenrtal board S132) works fine.
When trying...
Hello,
I test new SDK 13 and i have a problem. I don't success to debug bootloader. When i open .out file into debugger, sources are not complete (main is missing) so i...
Hello,
Is that possible to use a mbed application with SDK bootloader ? If yes, with signing too (if i sign application after generation) ?
How to set memory mapping...
I am trying to program an nRF52832 on an nRF52DK via the Debug in port (P18).
I am driving it with an STM32L073.
Should I put the nRF52832 into reset via the Debug in...
hai
in my application i am using nrf51822 . i have connected some sensors with the mcu. and i am collecting values from the sensors and this values are updated to the service...
In our code we use NV storage for system settings and calibration data.
I'm trying to understand when to open/close files and which structs to keep bwtween reads/writes...
Hello,
I'm using nrf51822/sd130/sdk12.1.0 and SOFTDEVICE_PRESENT defined.
But, I didn't enable softdevice.
I want to realize power save mode.
when I use __WFE...
hello there, i am using sdk11, i am using uart example. i am using nrf51 dk
SEGGER_RTT_WriteString is working. but
SEGGER_RTT_printf is not working. main.c
i have seen...
hello everybody,
i've downloaded the firmware files of nRF51822 beacon, but i couldn't find the source code. Does anybody know where i could find the source code of nrf51822...
Hello,
i try to use the nrfConnect (PC version) to update my devices via DFU. The DFU service is running on the device (update with Andoid nrfToolbox works without any...
Hi,
After finding that Windows doesn't like HID devices if they can't be bonded to, I've been attempting to add peer_manager and bonding into my application.
However...
Hi,
I'm working on a Custom Android app which connect to my NRF52 without any security.
This App is based on the UART demo App for Android, but I want that only my App...
I see that nRF52 SDK support the printf() , nrf_log_info() and app_uart_put() that can display data received on PC serial monitor, I'm wondering what's different/advantage...
I want to analyze the power consumption of connection parameter update procedure. How can i get a detailed description about the packet flow of it ? for example, the packet...
