Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi all,
i developer a code that :
press button short switch on one led
Press button long switch on two led.
but sometimes if i press the button a two led...
hi
i need store my data in internal flash memory (around 30kb). i have fixed memory map from 0x25000 to 0x35000. my,
block size = 16 byte,
block count =4096,
no of pages...
Hi,
I want to add functions of HID telephony to pickup/decline phone on nrf51822 application.
But it seems telephony usage did not work on android/ios phone, or incorrect...
hi :
I use Gzll protocol to realize 2.4G frequency hopping communication， One Device send data to One Host on Pipe2 receive. Now I use nrf24lu as "Host" and nrf51822 as ...
Hello,
My rigado BMD 200 board suddenly stopped responding. the Jlink interface cannot connect
I tried nrfjprog --recover with no success.(says cannot connect)
in segger...
I am using nrf51822 with sdk 6. I was using double bank ble dfu for the firmware upgrade. But now I have to switch to single bank dfu since my code size has exceeded the maximum...
hi ，
image 1 、
image 2、
image 3、
I now use nRF24LU1P for Bootloader upgrade, using the routine is the official website of the C# Lu1BootLdrTest project, nRF24LU1P...
Hi,
I have a nrf24lu1p usb dongle by hand and I want to know the flash size.The package marking is:
nRF D
LU1P16
1219AC
I am not sure whether the chip has a 16kB flash...
Based on multi-protocol add private agreement GZLL matching procedure, no matching success;But separate GZLL agreement can be successful, not any way to solve this problem...
Hey devs!
We'd like to add additional fields in the manifest.json when generating (or after generating) the zip file for DFU. We need these fields to make additional compatibility...
Hello,
I am using the nrf 52 dk with the soft 3.00. I am doing the Beacon Transmitter Sample Application from infocenter.nordicsemi.com/index.jsp.
I was able to compile...
Hi
I am using nrf52832 QFAA-R.
I wanted to know if there is a difference between SPIM current when SPIM is:
stopeed
started but not active.
Thanks
Yar...
While analyzing the current consumption of my nRF52832 Dev Kit I noticed that the system on low power current was significantly higher than expected. To further investigate...
i have connected the swdio , swclk , vcc , gnd , reset with the respective pins of the nrf52SDK ,but when am debug the nrf52sdk , am getting the following error.
ERROR...
