We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hello,
I would like to know if I can use nRF51822 chip to get partial BLE packet information like Access Address, PDU before the whole packet has arrived.
If yes how and...
Long title, but basically sums it up - is there any way to put the nRF51 into the off state from within the hard-fault handler if the soft-device was enabled prior to the...
Hi guys, I am trying how figure out the the devzone.nordicsemi.com/.../ works or ecuations to estimate the battery life using a central module.
My central device is battery...
Hello,
I am using nrf52832 board, with SDK 11.0.0 and s132_nrf52_2.0.0. and trying to program a 512 Bytes text file using nrfjprog (J-Link: JLinkExe) in flash.
The nrfjprog...
Can anyone on the Nordic Team provide some updates on these two projects in GitHub
pc-nrfconnect-boilerplate and pc-nrfconnect-core
Are they ready to start developing...
Hello developers,
I am trying to integrate ADC, TWI based MPU6050 for accelrometer with ble_nus service for data transmission. The ADC and MPU6050 works perfect but once...
I want to use sha256 library with S130, I have checked the documentation here developer.nordicsemi.com/.../a00985.html
Its very confusing and I have no luck yet, has anyone...
Hello,
Two years ago I develop a board with a nrf51822. Right now I'm trying to use the same board again. I installed the new SDK 12.3.0, GCC ARM, nrf command line tools...
Hi all,
I'm currently trying to get the UART example (no SoftDevice) to work under Segger Embedded Studio. What I know is, that retarget.c is used to redefine the neccesary...
Hello,
I've been implementing DAC control trough SPI and DMA using the NRF52 and it is working nicely. During development however I encountered what i think is a bug in...
Hello
i am using the NRF52 EvalBoard and a ADXL362 EvalBoard. I am trying to read every 100ms the FIFO buffer of the ADXL362. Below you can see my register configuration...
I can't get NRF_LOG working with SDK12.3.0.
Using the same main.c and sdk_config.h from SDK12.2 - here NRF_LOG is working well - I get no messages in J-Link RTT Viewer with...
I have made following connection between nordic device and external sound sensor:
VCC--> 5V
GND--> GND
GATE --> Pin 04
ENVELOPE --> A0
I would like to...
Hi all,
Can you give me an estimate about the power consumption required for the update Fw on OTA.
Our product has a solder batteries, so it's important know if in his...
I am using proximity profile using NRF52 DK.When i started measuring power consumption it is not at all coming less than 2mA.
In order to make as low power ,is there any...
