Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm pretty new with microcontrollers and SPI.
I connected fisically an nrf51822 microcontroller to an external SPI flash memory.
I connected MISO MOSI ports to some random...
I am using SDK 12.0.0.
I am working with low_power_pwm_init() to initialise the pwm and I have passed a handler while initialising. I want to stop the pwm from the handler...
Nrf52 SDK12.2 armgcc
I have a button on my device (peripheral) that when pressed starts a timer for 30 seconds.
During that 30 seconds, I would like to have the device...
Hi everyone,
I'm trying to use sscanf on my nordic device, and I get an issue with the following exemple (this same code works on my computer)
int d = 0;
float f =...
I have copied the blinky example:
/* Copyright (c) 2014 Nordic Semiconductor. All Rights Reserved.
*
* The information contained herein is property of Nordic Semiconductor...
.\_build\nrf51422_xxac.axf: Error: L6218E: Undefined symbol app_timer_init (referred from main.o).
.\_build\nrf51422_xxac.axf: Error: L6218E: Undefined symbol app_button_disable...
Hi all
Is possible have DFU in the peripheral side to update a Central app program? Is there example doing it?
I have a Peripheral (custom board nRF52 dongle) connected...
Hi
We use the nRF52832 together with other devices in a housing. Some of the other devices may produce quite a lot of heat. Therefore we wanted to use the temperature sensor...
Hi,
i am trying to flash the softdevice bootloader in Sparkfun nRF52832 breakout board using RPI2 + openOCD through SWD. debug port initialize is failed all the time.i...
I have a couple of questions regarding Radio transmission for BLE.
Is the radio driven by one of the HFCLKs? If so, it confuses me how a 16M clock can drive/derive...
Hi,
I have initial flashed boot loader and application based on SD version 3.1 and SDK 12.2.0
with
DFU_APP_DATA_RESERVED CODE_PAGE_SIZE * 3
FDS_VIRTUAL_PAGES 3...
I am using a nrf52 development kit as a peripheral to send data . It is working fine if I use the nrf Toolbox app on my phone, but is there anyway that I can see the 'raw...
Hi,
I configured openOCD and gcc compiler. But i got following error.
i gave following command on terminal.
i created one file that is manual.cfg
and contain in that...
Hi all,
someone can please explain to me how works the indication?
How can i read the value of cccd in the APP?My problem is understand if the APP is ready to receive...
First attempt at implementing buttonless dfu; assistance would be greatly appreciated. Using SDK v11 + s130 + nRF51822.
Please note that iphone screen captures supporting...
