Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I have a running board with NUS service (serial profile). This boards starts advertising until a remote device (android nrf UART app) connects to it. then it starts...
Hi, Nordic
I check this: devzone.nordicsemi.com/.../ , first, it will work when I follow this article. Then I have 2 questions:
it said "If the bootloader LED...
I am working on a project using a BLE Nano and Nordic sdk 8.1. I included the ble_flash.c, ble_error_log.c, and ble_debug_assert_handler.c files in my include path and c source...
I am running the Buttonless DFU example in SDK 12.2.0 on a nRF52832. When I connect with NRF Connect, I can see the DFU control point but I can only enable notifications and...
I learned that paring is consist of 3 phase (Exchange of Pairing Information, Authentication, Key distrbution) and TK, STK are generated at the phase of Authentication and...
I have a central application that I need to add a peripheral role to. I don't need to pair or bond in any of my connections, so I based my app on the ble_app_uart_c example...
Hi,
I'm currently running two separate TWI-instances on my nRF52 DK with SDK 11.
Each instance runs quite well with no issue, except for when instance 1 becomes active...
Hi,
When nrf51822 is connected via bluetooth LE to an iPhone application, is it possible to check the actual connection interval (between MIN_CONN_INTERVAL = 20ms and MAX_CONN_INTERVAL...
I have a project on a Ble Nano using Nordic SDK 8.1 that I currently compile entirely from terminal using a Makefile. I want to convert this project over to use Keil so I...
Dear sir,
I want to use NRF24LE1-F16Q48-R7 as a standalone controller in one of my application but it is not available with any vendor .
We want to use this For Low...
i want to know why there are 2 pages reserved although i mentioned i configured the number of pages to 1. It is used for what ? In fact, I need only one page for my data,...
Hi,
When compiling my program on SEGGER embedded studio I get the error:
Compiling ‘main.c’
main.c
expected expression before '{' token
in expansion of macro 'NRF_DRV_ADC_DEFAULT_CHANNEL...
I'm writing a central app using the pc-ble-driver project with an nRF51 dongle. This is to test our product, which is a peripheral using the nRF51822. The test central needs...
Dear All,
I have developed a BLE system in which nRF52832 is being used as a peripheral and central concurrently. I am also using BLE_GAP_CONN_SEC_MODE_SET_ENC_WITH_MITM...
Hello,
I have board pca10040 V 0.9.0 2015.41. When I program nrf and then issue a nrfjprog --reset -f NRF52 everything works fine, however when I execute nrfjprog --pinreset...
