Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello,
I am using nrf52840 PDK, sdk 13.0.0 for my college project. I am trying to rewrite this nrf mpu example , in order to read data from MPU9255 and observe the data in...
Hi l trying to hookup arduino primo and BMI160,but recently my develop is in a strange situation,that i sent 0x00 and others register but alway return 0xff, here shows the...
I want to check if some errors happened during the initialization before entering while(1) loop in the main. I am using nrf_CLI in my application (SDK 14.2.0 and S140 on nRF52840...
Dear Nordic Team,
Tanks for Supporting.
How to start test DFU in SDK12.3.0. My Hardware is PCA10028.
How to merge hex files soft device and bootloader ?
update 1...
I need to count millis from nrf52 start
I have seen that all are using rtc1 but I did not find any example from which i can integrate it to my project.
We are in the development stage of a product that uses the nRF52832 and have acquired a nRF6707 Rev 1.1.0 power profiler kit to make power consumption measurements.
I am...
Hi,
I'm trying to download Invensense's "Embedded MotionDriver 6.12" in order to compile the Thingy:52 SDK, as suggested here .
It seems that this wasn't previously...
Hi everyone,
I am currently trying to implement USB headset on nrf52840. As far as I can see the audio example from SDK14 uses SyncType=None meaning that bmAttributes bits...
I want to change type from "uint32_t val1 = 0xAA01" to "uint8_t val2 = {"AA01"}.
Then, attr_char_value.p_value = val2;
=> sd_ble_gatts_characteristic_add(p_rms->service_handle...
I am currently trying to develop Mesh applications using the Nordic Mesh SDK and the nRF52840 Dev kit. The problem that I am having is that my testing equipment isn't able...
We have a custom hardware device that uses the nRF51 and the S130 softdevices. We are able to connect our device to our app on iOS and Android and through a web-bluetooth...
I want to erase selected pages from the NRFflash memory (Not whole flash).
I have defined one function for NRF memory erase. In that, I have followed following sequence...
Hello, i am using NRF 52832 QFAA
In pstorage_platform.h I see
#define PSTORAGE_FLASH_PAGE_SIZE pstorage_flash_page_size()
and the return value of pstorage_flash_page_size...
Hi Nordic,
I have been quiet for a long time but here is another question.
For the project I am working on I want to measure the current with the PPK. Although it seems...
Hello. When I received nRF52DK, I have successfully uploaded some examples also with softdevice through the Keil IDE. But after few days Keil and also Segger IDE stopped detect...
