I'm building a project where I need to sniff bluetooth data exchanged between a Voltcraft SEM6000BT plug and my phone app. The idea here is to capture the BTATT (where the...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
We are building project with this config parameters: But we get this error messages while compile: If we use CONFIG_LOG =n for mcuboot, then project compiles normally. Also...
I'm developing a solution using the nRF9160 and would like to confirm the correct method to completely disable NB-IoT mode so the device operates exclusively in LTE-M.
...
Hello Nordic team, We are trying to use ST7305 display (custom driver that we have developed using st7789V as refrence ) and acconeer A121 senors on same SPI bus. The A121...
Hello, as from title, after updating from ncs 2.7.0 to 3.0.2 my application cannot advertise and scan concurrently anymore.
If I start advertising after starting a scan...
Hello,
I am using the NRF54L15 DK for development. I have configured the i2c with P1.12 as SCL and P1.14 as SDA.
below is my code in .overlay file
Below is the code...
I started with the ble_app_template and a preexisting project written with sdk 12.
I have a custom service and 2 characteristics.
The point I am at now is that my DK advertises...
Hi,
I am doing a beacon application. I am advertising sensor data. I am facing issue with advertising.
When I am powering the hardware using usb cable, my device is working...
Hi,
I am trying to interface external flash with the nrf52. I am able to read the device id. After writing to the status - configuration - bank address registers, I am...
I'm finding a good topic for my thesis which come in the next semester. Has TSCH for nRF52DK be implemented on Contiki OS? If not yet, I want to implement this. It is easily...
I try multiple pins set. My pro code is here.
But this is not clear. I want to decrease my code line. Then I tried this.
I want to know where is my mistake?
I am trying to create a TDMA based network with the nRF24LU1+. I understand that nRF51 and nRF52 have the ability to trigger the transmission of a radio packet upon timer...
I'm using an nRF52 (PRX) to communicate with with an nRF24L01+ (PTX) using ESB. As part of a pairing routine they need to switch channel and addresses. I've confirmed that...
I have been working on this for very long time but I can't figure it out, I am trying to use pc-ble-driver to connect my Ubuntu/Raspberry pi to by BT832X module over UART...
I flashed firmware into my nordic nrf52832 DVK
https://github.com/NordicSemiconductor/pc-ble-driver/blob/99b5e78f96de60ee70e749bb89b280116275fb97/hex/sd_api_v3/connectivity_1...
Hello,
I envisage to use beacon as anti-theft system:
When the beacon (inside the product to protect) will be near (2m) from the door, it will trig an alarm. So a receiver...
Hi,
I want to implement Extended Advertising for broadcasting data with LE Coded PHY on the nRF52840 Boards with Softdevice S140 v6.0.0.
For Soft Device Version S132...
This is basically a bug report/feature request, but I figured having it out in the open would be good too in case anyone else runs into this.
Hi Nordic folks,
Would...
Hi Expert,
I know how to read mac address by software ,
but I need to know how to read mac address by tool like nrfgo,
I tried nrfgo and nrfjprog but failed,would...
